E-3
1. READ INSTRUCTIONS -
2. RETAIN INSTRUCTIONS -
3. HEED WARNINGS -
4. FOLLOW INSTRUCTIONS -
5. CLEANING -
6. ATTACHMENTS -
7. WATER AND MOISTURE -
8. ACCESSORIES -
9.
10. VENTILATION -
11. POWER SOURCES -
12. GROUNDING OR POLARIZATION -
ALTERNATE WARNINGS -
13. POWER-CORD PROTECTION -
All the safety and operating instruction should be read before the product
is operated.
The safety and operating instruction should be retained for future
reference.
All warning on the product and in the operating instructions should be adhered to.
All operating and use instructions should be followed.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a dry cloth for cleaning.
Do not use attachments not recommended by the product manufacturer as they
may cause hazards.
Do not use this product near water- for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow the manufacturer's instructions, and should
use a mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may causethe appliance and cart
combination to overturn.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instruction have been adhered to.
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended to operate from battery power, or
other sources, refer to the operating instruction.
This product may be equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarizes plug.
This product is equipped with a three-wire grounding-type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact you electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and point where they exit from the product.
IMPORTANT SAFETY INSTRUCTIONS
14. PROTECTIVE ATTACHMENT PLUG -
15. OUTDOOR ANTENNA GROUNDING -
The product is equipped with an attachment plug having
overload protection. This is a safety feature. See Instruction Manual for replacement or resetting
of protective device. If replacement of the plug is required, be sure the service technician has used
a replacement plug specified by the manufacturer that has the same overload protection as the
original plug.
If an outside antenna is connected to the receiver, be sure
the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
E-4
SEE FIGURE:
NEC - NATIONAL ELECTRICAL CODE
GROUND
CLAMP
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
16. LIGHTNING -
17. POWER LINES -
18. OVERLOADING -
19. OBJECT AND LIQUID ENTRY -
20. SERVICING -
For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product due to lightning and power-line
surges.
An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards, Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally be following the operating instructions. Adjust only
those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to damage and will often require extensive work by a qualified technician to restore
the product to its normal operation.
e) If the product has been dropped or damaged in any way, and
f ) When the product exhibits a distinct change in performance -
this indicates a need for service.
When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards,
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating condition.
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
21. DAMAGE REQUIRING SERVICE -
22. REPLACEMENT PARTS -
23. SAFETY CHECK -
24. WALL OR CEILING MOUNTING -
25. HEAT -