background image

www.PyleUSA.com

1

2

IMPORTANT SAFETY INSTRUCTIONS

Read Instructions

Retain these safety and operating instructions for future reference. Heed all warnings 

printed here and on the equipment. Follow the operating instructions printed in this 

user guide.

Do not open

There are no user serviceable parts inside. Refer any service work to qualified technical 

personnel only.

Power Sources

Only connect the unit to mains power of the type described in this user guide or 

marked on the rear panel. The power source must provide a good ground connection.

Power Cord

Use the power cord with sealed mains plug appropriate for your local main supply as 

provided with the equipment. If the provided plug does not fit into you outlet consult 

your service agent. Route the power cord so that it is not likely to be walked on, 

stretched or pinched by items placed upon or against.

Grounding

Do not defeat the grounding and polarization means of the power cord plug. Do not 

remove or tamper with the ground connection on the power cord.

Moisture

To reduce the risk of fire or electrical shock, do not expose the unit to rain, moisture or 

use in damp or wet conditions. Do not place container of liquid on it, which may spill 

into any openings

Heat

Do not locate the unit in a place close to excessive heat or direct sunlight, as this could 

be a fire hazard. Locate the unit away from any equipment, which produces heat such 

as: power supplies, power amplifiers and heaters.

Environment

Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid 

tobacco ash, drink spillage and smoke especially that associated with smoke machines.

Handling

Protect the controls from damage during transit. Use adequate padding if you need to 

ship the unit. To avoid injury to yourself or damage to the equipment take care when 

lifting, moving or carrying the unit.

Servicing

Switch off the equipment and unplug the power cord immediately if it is exposed to 

moisture, spilled liquid or the power cord or plug becomes damaged during a 

lightning storm or if smoke odor or noise is noted. Refer servicing to qualified technical 

personnel only.

Installation

Install the unit in accordance with the instruction printed in the user guide. 

CAUTION

RISK OF ELECTRlC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

This symbol, wherever it appears, alerts you to 
the presence of uninsulated 

Dangerous

 voltages 

inside the enclosure that may be sufficient to 
constitute a risk of shock. 

This symbol, wherever it appears, alerts you to 
important operating and maintenance 
instructions in the accompanying literature.
Please read the manual.

Summary of Contents for PAD15MXU






Reviews: