4 – PYLE PRO PYX-3X Electronic Crossover Network
Owner’s Manual
PYLE PRO PYX-3X Electronic Crossover Network
Owner’s Manual
- 5
Caring for your PYX-3X Electronic Crossover Network
This component uses a 250V 0.5A fuse for protection from
power surges and short circuits. If the unit suddenly shuts
down and will not turn on, it is likely that this fuse has
blown.
To replace the fuse:
1. Locate the fuse holder on the rear of the cabinet and
unscrew the fuse compartment cap.
2. Remove the old fuse and replace it with an identical,
serviceable fuse.
CAUTION! Never use a fuse with a higher rating!
3. Replace the fuse compartment cap.
Turning the PYX-3X on
1. Turn on the audio input source equipment which is
connected to the PYX-3X INPUT jacks.
2. Set the LOW, MID and HIGH volume level controls to their
minimum level settings.
3. Adjust the crossover frequency points to suit your audio
system installation.
4. Push in the power switch to turn the amplifier on.
5. Adjust the LOW, MID and HIGH volume level controls to
the desired volumes.
Connecting to standard AC power
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
Mounting the PYX-3X
The PYX-3X is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
Tightly secure four mounting screws (not supplied) through
these fours slots and into your standard electronics equipment
rack.
PYLE
PRO
Audio,
Inc.
1600
63rd
Street
Brooklyn,
NY
11204
Place
Stamp
Here
Please
complete
warranty
card,
detach
and
return
PYX-3X Specifications
Input Impedance
Crossover Frequencies
Low
Mid (High Pass)
Mid (Low Pass)
High
Filter Slope
Total Harmonic Distortion
Frequency Response
S/N Ratio
Power Requirement
Power Consumption
Dimensions, inches (mm)
>47 K-Ohms
50, 90, 180. 360 and 720 Hz
50, 90, 180. 360, 720 Hz and Flat
1K, 2K, 4K, 6K, 8KHz and Flat
1K, 2K, 4K, 6K and 8KHz
-12dB/Octave
<0.01%
20 Hz - 20KHz (+/- 0.5 dB)
90 dB
AC 110V/60Hz or 230V/50Hz
6W
18
7/8
x 2
3/8
x 7
7/8
(180 x 60 x 200)
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the amplifier.
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully packed
and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing with the
product
• Include in your letter your return address, daytime phone number and
R.A. number
• Also include a check or money order for $15.00 for return shipping,
handling and insurance, or provide your Visa/MC number with
expiration date.
Our obligation under this warranty is limited to the repair or replacement of
the defective unit when it is returned to us prepaid. This warranty will be
considered void if the unit was tampered with, improperly serviced or subject
to misuse, neglect or accidental damage.
Limited Warranty