20
TEST TONE, LFE TRIMMER AND CHANNEL SELECT.
TEST TONE
Speaker Level balance Adjustment
The test tone function is useful to adjust the relative
volume between speakers in DOLBY DIGITAL or
DOLBY PRO LOGIC II mode.
Once the balance is set, you don’t have to change the
balance as long as the speakers aren’t moved.
1. Adjust the
MASTER VOLUME
to the normal
listening level. (Half of max. Volume is
recommended)
2. Press
the
TEST TONE
button (on the remote control)
in DTS, Dolby Digital or Dolby PRO LOGIC II
mode.
The test tone is emitted from each speaker each time you
press “
TEST TONE
”.
TEST
TONE
BASS
SURROUND
MODE
MEMORY
TREBLE
TEST
TONE
LFE TRIM
VOLUME
CH
SELECT
SUBWOO FER
ON /OFF
INPUT
SELECT
BAN D
ST/MO NO
TUNING
TUNING
AUTO
MAN UAL
DELAY
TIME
MUTE
POWER
INPUT
MODE
STATION
DYN AMIC
DIMMER
DO LBY
DIG ITAL
DO LBY PL
II
SPK
SETUP
VOLUME
P T-69 0A
→
L(FRONT LEFT)
→
R (FRONT RIGHT)
→
LS (SUR. LEFT)
→
←
SUB
←
C (CENTER)
←
RS (SUR. RIGHT)
3. Select a speaker by pressing the
“TEST TONE”
button and adjust the level by pressing the
MASTER
VOLUME
button.
The level of each speaker can be adjusted in 1 dB step
from –10 dB to +10 dB.
4. When the setting is finished, press the TEST TONE
button to stop the test tone.
Note:
You must keep press
TEST TONE
until one
complete cycle is finished.
LOW FREQUENCY EFFECT (LFE MIX)
LFE (LOW FREQUENCY EFFECT) MIX LEVEL
(LFE MIX)
Under COAX./OPT mode, when playing , input AC3 or
DTS 5.1CH signal, LFE will appear on the VFD, then
press LFE key on the remote, and again press VOL +/-
key to adjust the level between 0dB to –10dB.
Note:
The
LFE
adjust state resume to normal, if
MASTER VOLUME is not press after 5 seconds.
TEST
TONE
BASS
SURROUND
MODE
MEMORY
TREBLE
TEST
TONE
LFE TRIM
VOLUME
CH
SELECT
SUBWOO FER
ON /OFF
INPUT
SELECT
BAN D
ST/MO NO
TUNING
TUNING
AUTO
MAN UAL
DELAY
TIME
MUTE
POWER
INPUT
MODE
STATION
DYN AMIC
DIMMER
DO LBY
DIG ITAL
DO LBY PL
II
SPK
SETUP
P T-69 0A
LFE TRIM
CHANNEL SELECT
Balancing volume between speakers in 5.1 channel
mode when using the 5.1 analogue inputs.
As the Dolby Digital signal is decoded in the external
source, sometimes, you may have to balance volume
between speakers due to the location of speakers. In this
case:
TEST
TONE
CH
SELECT
BASS
SURROUND
MODE
MEMORY
TREBLE
TEST
TONE
LFE TRIM
VOLUME
CH
SELECT
SUBWOO FER
ON /OFF
INPUT
SELECT
BAN D
ST/MO NO
TUNING
TUNING
AUTO
MAN UAL
DELAY
TIME
MUTE
POWER
INPUT
MODE
STATION
DYN AMIC
DIMMER
DO LBY
DIG ITAL
DO LBY PL
II
SPK
SETUP
VOLUME
P T-69 0A
1. Press
“CH
SELECT
” on the remote, the following
loop will appear on the display:
→
L(FRONT LEFT)
→
R (FRONT RIGHT)
→
LS (SUR. LEFT)
→
←
SUB
←
C (CENTER)
←
RS(SUR. RIGHT)
←
2. Adjust
the
Master Volume
to balance all speakers.
The level of each speaker can be adjusted in 1 dB
steps from –10 dB to +10 dB.
Note:
If the
Master Volume
is not adjusted for 5 seconds in
Channel Trimmer state, it returns to normal state.
