Battery Installation
Select / Switch File Folder and Other Settings
About Recording Files
About the Card and Basic Operation
Push to open the battery cover.
Insert 2 “AA” size batteries with
correct polarity.
Open the SD card door,push the card fully
until it clicks. Being careful about the direction
you insert it.
Press and hold the PLAY/STOP key more than
two seconds, and the red indicator will flash,
then enter into the default status --- voice mode.
.
Press PLAY/STOP key more than two seconds
，
then the LCD goes out ,and the unit is turned off.
Close the Card door .
* If the card door cannot be completely closed,
remove the card ,check its direction and then
insert it again.
Close the battery cover.
* The batteries are fresh.
* The batteries are exhausted, and need to be charged up
or replaced.
Note:
If necessary , it may provide power supply by connecting the unit ( USB jack ) to
a PC by USB cable ,or connecting the unit ( DC jack ) to electrical outlet by AC Adapter.
It will never affect files stored in the unit to replace batteries . If you shut down the unit with normal
operation , it will keep the date and time by previous setting .
BATTERY INDICATIORS:
At voice mode, press the “A-B” key to switch
file folder .
There are four memory storage areas(file folders) labeled A,B,C,D in the unit for your
choice , it can store 99 files in each file folder , so it can store 396 in all . Absolutely ,it
must be subject to its memory capacity .
Slide the HOLD switch to the “ ON ” (Lock) position,
then all buttons lose function .
Slide the Mic Selector switch to the “ST” or “MONO” position
according as your demand ,and “ ST ” or “ MONO ” appears
on LCD as right photos . ( “ ST ” is stereo. )
As the right photo , it shows the file folder name
on LCD .
* The Factory setting is “A” .
At voice mode , press key ,it shows the recording
date and time about this file ,as right photo .
Slide the HOLD switch to the “ OFF ” position to
recover all buttons function.
Note :
Please keep at least
50mm
away
from the sound source
for optimal quality.
* If the L/R Peak indicator blinks ,it means the external
volume is too high ,so you may adjust the Rec level turn
knob .
Inserting and removing the Card
To turn on/off the unit
Select a file folder
At voice mode ,you may select a desired file folder by
“A-B” key , and you may set VOX function at first . ”VOX”
appears on LCD while recording .
Before recording , you can set the VOX function according as your demand . If it is turned
on , if the detected volume doesn’t reach the VOX level value set in advance, recording will
pause until it detects eligible volume ( VOX switch operation refers to page 9 ).Otherwise
it will continue recording soundless section in this file .
Tumble the Rec Level turn knob to adjust the REC
level while recording, it shows the Rec Level wave along
with the roll turn knob as the right photo .
(The longer wave the higher voice it can record.)
Preparing for recording
After finishing preparing operation , just press REC/
STOP key once , then the REC record indicator
blinks ,and the current status displays on LCD, but at
this status, it will not record. Now you may also adjust
the Rec level value according as the external volume
by Rec Level Control .
Then press REC/STOP or ERASE/PAUSE key to start recording
and timing .However ,if you press Mode key ,it will cancel recording
to return to voice mode .
If you need
to
paus
e
, press
the
ERASE/PAUSE key .Then REC indicator
blinks ,it stops recording and timing until you press REC/STOP or ERASE/
PAUSE key .
Recording file
HOLD and mic selection function
Note :
The name at the left of the LCD indicates the
current file. The number at right indicates the total time
recorded of the selected file folder.
If the unit is full, “ FULL” will appear on the LCD . Delete or
move files,or change another new SD card , it may record
right along .
* The first several minutes sound may not be
recorded for activating the recorder .
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1.Only use the battery with specified size and type .
2.Be sure to follow the correct polarity when installing the batteries as indicated on the
battery compartment .Reversed polarity may cause damage to the device .
3.Do not mix different types of batteries together (e.g.Alkaline and Carbon-zinc ) or old
batteries with fresh ones .
4.If the device would not be used for a long period of time ,remove batteries to prevent
damage or harm from possible battery leakage .
5.Do not try to recharge batteries without rechargeable function , or they will
overheat and rupture .( Follow battery manufacturer’s directions .)
6.Never try to remove the batteries while using .
