background image

INCHES OF PITCH

Diameter and pitch must be 

calculated as if Max-Prop Easy was 

a normal fixed propeller. Max-

Prop Easy then offers the great 

advantage of pitch adjustability in 

order to optimize the performance 

of the propeller. If the engine does 

not reach the desired RPM, reduce 

the blade angle; on the contrary, 

if the engine exceeds the desired 

RPM, increase the blade angle.

The Max-Prop Easy allows an angle 

variation of 2° increments, this 

corresponds to a variation in the 

engine RPM of about 13% at the 

same boat speed. It’s possible 

to change either the pitch to optimize the engine performance, or the rotation (for ex. if you 

change the engine, or if there was a mistake when ordering the prop). If you have doubts about 

the rotation: shaft rotation is determined from the stern of the boat looking forward. With the 

engine in forward position clockwise rotation of the propeller means it is right hand “R”, and a 

counterclockwise rotation is a left hand “L”.

Pitch and rotation of the Max-Prop Easy can be changed as follows:

On the body of the propeller are two threaded bores, marked with letters “R” and “L”; within 

these bores are placed two bolts. 

The pitch of the propeller, both in forward and reverse position, can be easily varied by changing 

the supplied bolts threaded into the body of the propeller with other bolts of a different length. 

The pitch in forward rotation varies by changing the bolts placed in bore “R” if the propeller is 

right-handed or changing the bolts placed in bore “L” if the propeller is left-handed.   The list of 

the pitch regulation bolts, that are supplied with every Easy propeller is indicated in fig.4. 

For example inserting the #20 bolt in the forward rotation and 2 in the reverse rotation will 

provide a 20° angle for both front position and reverse rotation. Varying 1mm the length of the 

bolts, blades inclination has a 2° variation 

Blade 

Angle

Right Rotation

Left Rotation

Forward 

Bore “R”

Reverse 

Bore “L”

Forward 

Bore “L”

Reverse 

Bore “R”

16°

16

1

16

1

18°

18

18

20°

20

2

20

2

22°

22

22

24°

24

3

24

3

Fig.5 - Close up of the Left and 

Right pitch adjustment bolts.

Fig.3b

Fig.4

5

TIP:

 Watch our YouTube video on how to adjust

the pitch, visit 

https://youtu.be/HJsnHCi2U6U

Or scan the QR code with a mobile device. 

Summary of Contents for Max-Prop EASY 2 Blade













Reviews: