EU Regulatory Conformance
Hereby, Pycom Ltd declares that the radio equipment type Wipy
3.0 is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet
address:www.pycom.io
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with
the instructions, may cause harmful interference to radio
communications.However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
RF Warning Statement
To comply with FCC RF exposure compliance requirements,
the antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device is intended only for OEM integrators under
the following conditions:
1) The antenna must be installed such that 20 cm is
maintained between the antenna and users, and
2) The transmitter module may not be co-located with any
other transmitter or antenna.
As long as two conditions above are met, further transmitter
test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional
compliance requirements required with this module installed.
To ensure compliance with all non-transmitter functions the
host manufacturer is responsible for ensuring compliance
with the
module(s) installed and fully operational. For example, if a host
was previously authorized as an unintentional radiator under the
Declaration of Conformity procedure without a transmitter
certified module and a module is added, the host manufacturer is
responsible for ensuring that the after the module is installed and
operational the host continues to be compliant with the Part 15B
unintentional radiator requirements.
The module is limited to OEM installation ONLY.
The module is limited to installation in mobile or fixed application.
We hereby acknowledge our responsibility to provide guidance
to the host manufacturer in the event that they require
assistance for ensuring compliance with the Part 15 Subpart B
requirements.
IMPORTANT NOTE:
In the event that these conditions
cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID
cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for reevaluating the
end product(including the transmitter) and obtaining a
separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where
the antenna may be installed such that 20 cm may be maintained
between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains FCC ID:
2AJMTWIPY3R”. The grantee's FCC ID can be used only when all
FCC compliance requirements are met.
The following FCC part 15.19 statement has to also be
available on the label:
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Manual Information to the End User
The OEM integrator has to be aware not to provide information
to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates
this module.
In the user manual of the end product, the end user has to be
informed that the equipment complies with FCC radio-frequency
exposure guidelines set forth for an uncontrolled environment.
The end user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could
void the user's authority to operate this equipment.
The end user manual shall include all required
regulatory information/warning as show in this manual.
The maximum operating ambient temperature of the equipment
declared by the manufacturer is
-20~+85C
