PV Powered 1100 Installation And Operation Manual Download Page 32 | Manualshive

Page: 32 / 42

PV Powered 1100 Installation And Operation Manual Download Page 32

Grid-Tied Residential Inverters

Installation and Operation Manual

25

6. Limited Warranty

6. LIMITED

W
ARRANTY

PV Powered, Inc. provides a limited warranty for your residential or commercial inverter

and optional data monitoring module for defects caused by material or manufacturing

ﬂaws. The inverter and the data monitoring module must be installed and maintained by a

qualiﬁed installer in order for the warranty to be valid.

6.1 Terms of Coverage

The warranty period for the inverter is ten years, and the warranty on the data monitoring

module is one year, each beginning on the date of purchase by the original end user.

6.2 Coverage

PV Powered will, at its option, repair or replace the defective component(s) free of

charge, provided that you notify PV Powered of the defect during the warranty period,

have a dated proof of purchase, and PV Powered determines that the defect is covered

by the limited warranty set forth above. PV Powered reserves the right to inspect the

defective component(s) and determine if the defect is due to material or manufacturing

ﬂaws. PV Powered also reserves the right to charge a fee for service time expended if the

defect is not due to material or manufacturing ﬂaw or is not for some other reason subject

to this limited warranty.

PV Powered will, at its option, use new and/or reconditioned parts in performing

warranty repair and in building replacement products. PV Powered reserves the right to

use parts or products of original or improved design in the repair or replacement. If PV

Powered repairs or replaces a product, its warranty continues for the remaining portion

of the original warranty period or 90 days from the date of the return shipment to the

customer, whichever period expires later. All replaced products and all parts removed

from repaired products become the property of PV Powered.

For defects covered by this limited warranty, PV Powered will provide, at no additional

cost to the customer, both parts and labor necessary to repair the product, and return

shipment to the customer via a PV Powered selected, non-expedited, surface freight

carrier within the United States and Canada.

«
...
30
31
32
33
34
...
»

Summary of Contents for 1100











































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands