PV Electronics Elite Nixie Assembly Instructions And User Manual Download Page 23 | Manualshive

Page: 23 / 43

background image

Nixie Tube Clock ‘Elite’

Issue 3 (25 July 2018)

www.pvelectronics.co.uk

- 23 -

5.11 SET, ADJ, DST, ALARM (Push button switch)

Only solder the two pins closest to the board edge. The other two
pins are the frame and are not electrically connected. By only
soldering the two active pads, if you make a mistake it is much
easier to remove or re-position the switches!

It is easier to solder one pin per switch first, then re-position by
rewetting the pad until the switch is fully pushed into position.
Then solder the second pin.

5.12 D6, D8 (3mm Yellow LED)

Using the LED bending jig, bend D6 and D8 as shown below.

«
...
21
22
23
24
25
...
»

Summary of Contents for Elite Nixie












































Reviews:

No comments

Related manuals for Elite Nixie

Brand: La Crosse Technology Pages: 9

Brand: La Crosse Technology Pages: 10

Brand: La Crosse Technology Pages: 5

Brand: La Crosse Technology Pages: 4

Brand: La Crosse Pages: 6

Brand: La Crosse Technology Pages: 2

TIMER MINI DIGI

Brand: Reichelt Pages: 2

Brand: Zetronix Pages: 13

60.2009 Cone Wake-up Light

Brand: TFA Pages: 20

Brand: Magnavox Pages: 21

Brand: Sylvania Pages: 11

QUARTZ MOVEMENT

Brand: WESTERSTRAND Pages: 8

Brand: WESTERSTRAND Pages: 15

Brand: Skyworks Pages: 19

Brand: Marathon Pages: 4

2G-StarLink TrackerSF

Brand: ERM Pages: 17

Smart Sound Controlled Cloud Alarm Clock

Brand: MUID Pages: 4

Brand: Craftmade Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands