128-9485
Page 8
(Alarm & Keyless Systems Only) PROGRAMMING YOUR CUSTOM OVERRIDE CODE
Unlike override switches easily found, and defeated, this security system allows the consumer to
program a personal override code, offering a higher level of security. To take advantage of this option,
programmable feature # 9 must be selected for the Custom Code Option. Consult your installation
center for programming details. The system comes from the factory with a preprogrammed override
code of 11. To change this default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency override sequence.
Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the Receivers push-button switch, 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep
and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the Receivers
push-button switch from 1 up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the Receivers
push-button switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position. If the new code was accepted, the unit
will report back the newly entered code, by flashing the LED, first indicating the 10ths digit,
pause and then the units digit. The unit will report the new code three times with a one second
pause between each code, then the system will begin arming. If the LED flash pattern reports
the previously stored code, the new code was not entered correctly. Please repeat steps 1
through 7 above considering the following.
NOTE:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or
no digit entered in any place, units or tenths.
NOTE:
If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds
during any of the above steps, the unit will revert back to the last successfully stored code.
CUSTOM CODE PROGRAMMING EXAMPLE
To Change the code from the factory preassigned code of 11 to “52” you would do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency override sequence.
2.
Turn the ignition switch to the on position.
3.
Within 10 seconds, press and release the Receivers push-button switch, 3 times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep
and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the Receivers push-button switch to set the
tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on.
7. Within 10 seconds, begin to press and release the Receivers Push-button switch to set the units
digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern.
You will notice the LED flashing five times, pause, and then flash two times, pause. This pattern will
be repeated three times indicating the new code (52) has been accepted and stored in memory.
NOTE:
If after step 7, the LED flashes a code other than what was just entered, this indicates that
the code has not been changed. You will have to repeat steps 1 through 7 above being
certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit
entered in any place, units or tenths.
NOTE:
If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds
during any of the above steps, the unit will revert back to the last successfully stored code.
Page 8