PURSUIT PR2LCD Operator'S Manual Download Page 1

128-9485

Page  1

Model PR2LCD

Operators Manual

RF Upgrade Kit 

Check with your installation center for features and functions operational on your system. 

To Operate System:

1) Press the lock button to lock the doors and arm the alarm if installed.  

2) Press the unlock button to unlock the doors and disarm the alarm if installed. 

3) Press and hold the Trunk/Start button for 3 seconds to unlock the trunk.

4) Press the Trunk/Start button two times in succession to start the vehicle.  The vehicle will start 

and run the predetermined time set up during installation (5 to 60 minutes selectable).  

Anytime during the run cycle, enter the vehicle by first unlocking the doors with your transmitter, 

insert your key and turn it to the run, NOT START, position, then step on the brake, the vehicle is 

now in control of the ignition key.

NOTE: 

 For push to start vehicles contact your installation center for proper procedure

.

Consult your installation center for operation and information on convenience options 1 & 2 

which may have been connected or added to your vehicle.

PATENTED:  www.voxxintl.com/company/patents

IGN

AM

PM

Z

Z

24

S

1 2

INHIBIT

A

0

Lock/Arm

Unlock/Disarm

Trunk Release/ Remote Start

Option

F

Function Button

Summary of Contents for PR2LCD













Reviews: