1. Prior to commencing assembly, check
Ego QuicKEY™
is set in the disengaged position.
Ego QuicKEY™
is set in the disengaged position when the Slider Bolts are positioned to the right of the Slots. Refer
Diagrams 1, 1a and 2.
2. If
Ego QuicKEY™
is set in the engaged position, insert the Handle (Item 14) into the Spindle and rotate
clock-wise. Refer Diagram 2.
3. Take the Quick Release Mounts (Item 2) and the Cross Bar (Item 3) and join together as per Diagram 3.
Loosely tighten the nuts, as you will be required to adjust these later.
4. Clip the Power Movers (Item 1) onto the Quick Release Mounts as per Diagram 4. This can be achieved
by tilting the back of the Power Mover upwards and slotting the tongue on the Carrier Body into the slot
on the Quick Release Mount. Once it is slotted in, lower the rear of the Power Mover. There is no need at
this stage to insert the Retaining Pin.
5. Place the Motor and Cross Bar Assembly, Diagram 3, on a mat and drag under the recreational vehicle
with the Rollers facing the wheels.
6. Raise the Assembly so that the centre axis of the Rollers is equal in height to the centre axis of the
Wheels and rest on a block of wood etc.
7. Tape the 20mm Spacers (item 31) to the Rollers at centre axis point.
8. Then move the assembly so that the Rollers with the Spacers attached are hard against the tyres.
9. Referring to Diagram 5, position one of the Chassis Plates (Item 4 - Left and Right hand version supplied)
on the inside of the recreational vehicle’s chassis so it is sitting slightly above the Cross Bar with the lip
facing inward.
10. Mark where the holes on the Chassis Plate align with the chassis on the recreational vehicle.
11. Remove the Chassis Plate and drill 3 holes sufficient for the three 70mm Bolts to be inserted.
12. Install the Chassis Plate and tighten the 70mm nuts and bolts.
13. Repeats Steps 9,10, 11 and 12 for the other side ensuring that both Chassis Brackets are in the same
position on each side of the recreational vehicle’s chassis.
14. Loosely fit the Chassis U-Plate (Item 10), the Upper Chassis Clamp Plate (Item 11) and the Lower
Chassis Clamp Plate (Item 12) to the Chassis Plate and Cross Bar with the Bolts, Nuts and Washers
supplied (Items 7, 8 and 9 and 13) as per Diagram 5.
15. Ensure the assembly is aligned on all points as mention previously, all components aligned with the
Chassis on the recreational vehicle, the Roller centre axis is equal to the centre axis of the Wheel and
each Roller identically spaced 20mm from the tyre. The Cross Bar can slide forward and backwards on
the Chassis Clamp Plates to enable you to achieve a 20mm spacing.
16. Ensure that each Power Mover is free to move forward and backward and does not obstruct the shock
absorbers or any other obstacle that is likely to interfere with their operation. Also ensure that the
gearbox on the Power Movers has a minimum distance of 10mm to the inner surface of the tyre when
in the engaged position.
17. Once correctly aligned tighten all Bolts and Nuts (Items 7, 8 and 9) to a torque setting of 55Nm.
18. Check the alignments of all assembled components and if correct tighten the Chassis Stop Bolts and
Nuts (Items 13) to a torque setting of 55Nm. The Chassis Stop Bolts and Nuts grip the lip of the Chassis
Bracket helping prevent the Power Movers from sliding along the chassis.
19. Fit the Retaining Pins to the Power Mover.
MECHANICAL ASSEMBLY and INSTALLATION INSTRUCTIONS:
Page 7
The Chassis Plates supplied with Ego QuicKEY™ are suitable for most recreational vehicles.
However some recreational vehicles require non-standard plates. Check with the dealer to
ensure you have the correct Chassis Plates to fit Ego QuicKEY™
EQR130 1308 Ego QuicKEY User Manual Final.indd 7
30/07/2013 2:33:25 PM
