PureTools PT-PSW-21KVM User Manual Download Page 11 | Manualshive

Page: 11 / 40

background image

User Manual

PT-PSW-21KVM

7

3.

EDID Management

EDID are control by the EDID DIP switch, the specific description is as follows:

⚫

0000 Learn the display EDID in the default mode: read the EDID of the TX
HDMI output and RX HDMI output, and output the EDID with the lower

resolution of the two, if you can’t learn it, then use the built

-in

1920x1080@60 8bit Stereo

⚫

0001 1920x1080@60 8bit High Definition Audio

⚫

0010 3840x2160@60Hz Deep Color Stereo Audio

⚫

0011 3840x2160@30Hz 8bit Stereo Audio

⚫

0100 3840x2160@30Hz Deep Color High Definition Audio

⚫

0101 3840x2160@60Hz 4:2:0 Deep Color Stereo Audio

⚫

0110 3840x2160@60Hz Deep Color High Definition Audio

⚫

0111 3840x2160@60Hz Deep Color HDR LPCM 6CH

⚫

1011 Custom EDID1

⚫

1100 Custom EDID2

⚫

1101 Custom EDID3

⚫

1110 Custom EDID41111 EDID management

«
...
9
10
11
12
13
...
»

Summary of Contents for PT-PSW-21KVM









































Reviews:

No comments

Related manuals for PT-PSW-21KVM

Brand: D-Link Pages: 2

WJSX150 - SWITCHER - ADDENDUM

Brand: Panasonic Pages: 48

Brand: Dataprobe Pages: 21

Brand: Black Box Pages: 2

SRS Lighting DTS16F-DIN

Brand: plasa Pages: 4

Brand: P-Link Computer Pages: 92

TM-1-8210 Series

Brand: Eaton Pages: 3

kontron KSwitch D4 MF

Brand: S&T Pages: 100

Universal Videohub 288

Brand: Blackmagicdesign Pages: 107

DOMINION KX II DKX2-0E-E

Brand: Raritan Pages: 257

Brand: WilTec Pages: 7

CheetaHub Classic-2041

Brand: Accton Technology Pages: 7

Brand: IBM Pages: 94

Brand: B&B Electronics Pages: 2

Brand: Hammond Pages: 2

AC-MX44/88-AUHD-HDBT

Brand: AVProEdge Pages: 32

iRC Electronic DPSI TWIN Mini

Brand: Emcotec Pages: 2

Brand: EtherWAN Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands