manualshive.com logo in svg

Puretec PT Series, User Manual

Share
Download
Puretec PT Series User Manual Download Page 3

3

 

PT Series

 | 

Caravan / RV Fresh Water Pump  

Features

Introduction

The Puretec PT Series Pump is designed to run economically for many years, dependent 
on the initial installation and periodical maintenance.

Features

• 

4 Chamber diaphragm pump

• 

Bypass to reducing cycling

• 

Dry Run Protection 

• 

Automatic operation controlled by pressure switch 

• 

Industry standard mounting pattern

• 

Self-priming

• 

Quiet operation 

Applications 

• 

Caravan / RV / boat pressurised water system 

• 

Sprayer fixtures (vehicle-mounted sprayers, electric sprayers)

• 

Cleaning machines, humidifier, water purification, medical apparatus

• 

Beverage filling & liquid transfer

• 

Solar water system 

• 

Any other small pressurisation system

 

Materials/Tools Required 

You will need the following materials/tools to install the PT Series pump:

• 

2 (or more) lengths of flexible, reinforced hose with a collapsing strength of twice the 

inlet pressure.

• 

4 x stainless steel hose clamps and screws

• 

4 x screws to fasten the pump to the mounting surface

• 

Electrical cutoff switch 

• 

15 AMP Fuse

• 

Screwdriver

• 

Strong cutting implement for tubing

• 

Thread seal tape 

Summary of Contents for PT Series













Reviews:

No comments

Brands by name

Popular brands

Load more brands