Pure Reliability Pilot 1200 Wash Product Manual Download Page 3

Pilot 1200 wash

EN.doc

3/16

When unpacking and before disposing of the carton check there is no transportation
damage before using the unit. Should there be any damage caused by transportation,
consult your dealer and do not use the unit.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away
from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water
or any other liquids.

The projector is not designed or intended to be mounted on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified
personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from
adjacent wall surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m.

5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation
conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power­cord is never crimped or damaged by sharp edges. Never let the
power­cord come into contact with other cables. Only handle the power­cord by the plug.
Never pull out the plug by tugging the power­cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is
supplied for this; it should be attached as shown in “installing the projector” section.

The lamp used in this projector is a PHLIPS MSR 1200 SA/DE discharge lamp. After
switching off don’t attempt to restart the projector until lamp has cooled, this will require
approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of
both the lamp and the projector. But occasional breaks will prolong the life of the lamp and
projector.

Never run the projector without a lamp.

There is no user serviceable parts inside the projector, do not open the housing and never
operate the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it
or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

SAFE USAGE OF THE PROJECTOR

Summary of Contents for Pilot 1200 Wash

















Reviews: