Pure Power Tools PUREANGGRINDER18 Original Instructions Manual Download Page 6

6

13. This is a two handed machine.

  

Never try to use this machine with one hand, 
and never use this grinder whilst sitting on 
the floor.

14. Sparks, dust and waste particles 
may be ejected during grinding 
operations.

 Use safety screens, if 

necessary, to protect and keep bystanders 
at a safe distance from operations.

ADDITIONAL SAFETY RULES FOR 
GRINDING DISCS

WARNING:

 Always read the Safety 

Instructions and advice printed on  
the Disc.

1. Speed.

 Check that the speed rating 

of the disc is compatible with the no load 
speed of the machine. Never use a disc with 
a speed rating less than the speed rating of 
the machine.

2. Always inspect the disc.

 Never use a 

disc that is chipped, cracked or damaged in 
any way. Disintegration of a damaged disc 
in use can cause serious injury. Defective 
discs MUST be destroyed.

3. Mounting and Handling.

 Bonded 

abrasive products are breakable and must 
be handled with great care. The use of 
damaged or incorrectly mounted abrasive 
discs is potentially very dangerous. 
Fragments from a disintegrating disc can 
cause serious injury.

4. Usage.

 Read the disc label for specific 

applications and user instructions, and 
observe any safety information. Do not use 
for any non-specified tasks. Wet grinding 
procedures must not be attempted with this 
machine.

5. Do not force the disc.

  Allow the speed of 

the disc to do the work. Never push or force 
the disc onto the workpiece as this could 
lead to disc damage and potential operator 
danger. Allow the disc to glide over the work 
surface, returning again and again until the 
desired finish is achieved. Trying to grind 
away too much of the work surface in one 
pass could lead the disc jamming and cause 
significant ‘kickback’ to occur.

6. Do not use reducing rings or bushes 
with this machine.

 Only use discs which 

are specially designed for this machine. It is 
not permissible to adapt discs not designed 
for use in this machine.

7. Handling and Storage.

 Bonded abrasive 

products must be handled, transported 
and stored with great care. Discs should 
be stored in a secure cupboard or 
similar where they will not be subjected 
to mechanical shock and any adverse 
environmental influences (freezing or 
very high temperatures, moisture ingress, 
sunlight damage etc). If possible store each 
disc in its own dedicated storage carton or 
box.

WARNING

This machine is not intended for use by 
persons (including children) with reduced 
physical, sensory or mental capabilities, 
or lack of experience and knowledge, 
unless they have been given supervision or 
instruction concerning the safe use of the 
machine by a person responsible for their 
safety.

Children should be supervised to ensure 
that they do not have access to, and are not 
allowed to play with, this machine.

Summary of Contents for PUREANGGRINDER18













Reviews: