PumpSpy PS2000 Installation And Operating Instructions Manual Download Page 8

© PumpSpy Technology, LLC   Questions? 

Email Tech Support:

 [email protected]

WHAT THIS WARRANTY COVERS
When used and maintained in normal use and in accordance with the Installation and Operating Instructions, your 
PumpSpy™ product is warranted against original defects in material and workmanship for a full three years from 
date of purchase (the “Warranty Period”). During the warranty period, PumpSpy™ will repair or replace at no cost 
to you, to correct such defects in products found upon examination by PumpSpy™ to be defective in materials or 
workmanship.

WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover use of the product in a non-residential application, improper installation and/
or improper maintenance of the product, damage due to misuse, acts of God, nature, vandalism or other acts 
beyond the control of PumpSpy™, owner’s acts or omissions, use outside the country in which the product 
was initially purchased and resales of the product by the original owner. This warranty does not cover pick up, 
delivery, transportation or house calls. However, if you mail your product to PumpSpy™ for warranty service, 
cost of shipping will be paid one way. This warranty does not cover products purchased from a party that is not an 
authorized retailer, dealer, or distributor of PumpSpy™ products.

OTHER IMPORTANT TERMS
This warranty is not transferable and may not be assigned. This warranty shall be governed and construed 
under the laws of the state of Ohio. The warranty period will not be extended by any replacement or repair 
performed under this warranty. THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED 
BY PumpSpy™. ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OR 
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT WILL 
PumpSpy™ BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF 
ANY KIND OR NATURE TO OWNER OR ANY PARTY CLAIMING THROUGH OWNER WHETHER BASED 
IN CONTRACT, NEGLIGENCE, TORT OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE 
WHATSOEVER. Some states do not allow for the exclusion of consequential damages, so the above exclusion may 

not apply to you. This warranty gives you specific rights. You may also have others that vary state to state. 

Installed by:______________________

Date of Installation:_________________

Model: PS2000

Serial Number:_____________________

83019-04

LIMITED THREE-YEAR WARRANTY

Summary of Contents for PS2000









Reviews: