manualshive.com logo in svg

PumpSpy PS2000, Installation And Operating Instructions Manual

Share
Download
PumpSpy PS2000 Installation And Operating Instructions Manual Download Page 1

© PumpSpy Technology, LLC   Questions? 

Email Tech Support:

 [email protected]

IMPORTANT!

READ ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USING THIS PRODUCT.

Save these instructions for future reference. Failure to read and follow the warnings and instructions 

within this instruction manual could result in property damage, serious injury or death.

INSTALLATION AND OPERATING INSTRUCTIONS

ELECTRONICS AND PUMP COMPONENTS ASSEMBLED IN THE USA

MONITORING SOFTWARE AND TECHNOLOGY MADE IN THE USA

12 VDC Sump Pump

System Solid State Pump Controller

Power Supply Requirements  

12 VDC

Motor 

Brushless DC

AMP Rating 

18 Amps

Temperature Rating 

40°F to 120°F

Discharge 

1 1/2” NPT

MAX Flow 

3000 GPH

Power Supply Requirements  

 120 VAC, 60 Hz, 
15 AMP

Electrical Ratings 

 

12Amps @ 120 VAC; 
18 Amps @ 12 VDC

Relative Humidity 

0 to 80%

Storage Temperature 

0° to 70°C

Operating Temperature 

0° to 50°C

SPECIFICATIONS

PumpSpy

™

 PS2000

PumpSpy Technology | [email protected]

34000 Lear Industrial Parkway,  Avon, OH 44011

®

PUMP

SPY

The PumpSpy System requires a 12V Deep Cycle Battery (not included), 40 amp/hr 

minimum, 75 amp/hr or higher recommended. SLA/AGM Battery strongly recommended.

WIFI CONNECTED BATTERY BACKUP

 

SUMP PUMP & MONITORING SYSTEM

24/7 AUTOMATED REMOTE SUMP PUMP MONITORING

Summary of Contents for PS2000









Reviews:

No comments

Brands by name

Popular brands

Load more brands