background image

11

ASSEMBLY

• Parts needed - 1 foot, 1 M8 lock nuts.

• Raise or tilt pressure washer so you can line up foot with the hole located at the centre of the frame.

• Align the rubber foot with the hole in the frame where the foot is to be located. Attach foot by inserting the bolt from the 

bottom up and install the acorn nut. Wrench tighten until there is a slight crush on the frame tube. (Do not over tighten)

Attaching Foot Assembly (See fig 1)

Install Handle (See fig 2)

• Install upper frame (handle) onto the lower frame by sliding the handle over the two upright tubes on the lower frame 

and pressing down firmly until the handle is seated and the bolt holes align.

FIG 2

FIG 1

• Attach the upper gun hook, install two plastic rivets, until the plastic rivets are snug, you may need to tap with a mallet 

or small hammer to seat the lock pin.

• Attach the lower gun hook, install the M6 screw & lock nut, wrench tighten until the nut is snug,  do not over tighten.

Attaching Upper and Lower Gun Hooks (See fig 3)

• Attach the accessory hook.

• Install two plastic rivets, until the plastic rivet is snug.

• You may need to tap with a mallet or small hammer to seat the lock pin.

Attaching Accessory Hook (See fig 4)

FIG 4

FIG 3

1

2

Summary of Contents for W31H19
























Reviews: