manualshive.com logo in svg

Pulsar PSBEN 5012E, Manual

Share
Download
Pulsar PSBEN 5012E Manual Download Page 6

www.pulsar.pl   

 

 

 

PSBEN5012E   

 

 

 

    

BLACK POWER

 

 
 

6 

3.  Technical description. 

 

3.1  General description. 

The  buffer  power  supply  is  designed  in  accordance  with  the  requirements  of  the  EN  50131-6  standard, 

grade 1÷3 and II environmental class. It is intended for an uninterrupted supply  of alarm system devices requiring 
stabilized voltage of 12V DC (+/-15%). 

Depending  on a required  protection level  of the alarm system in the  installation  place, the  PSU efficiency 

and the battery charging current should be set as follows: 

 
* Grade 1, 2 - standby time 12h  

 

 

 

 

Output current 4,1A + 1,5A battery charge 

 
** Grade  3 - standby time 30h if the faults of the main power source are reported to the Alarm Receiving 
Centre - ARC (in accordance with 9.2 

– EN 50131-1 standard). 

 

 

 

Output current 2,16A + 3A battery charge 

 

 

      

-  standby  time  60h  if  the  faults  of  the  main  power  source  are  reported  to  the  Alarm  Receiving 

Centre - ARC (in accordance with 9.2 

– EN 50131-1 standard). 

 

 

 

Output current 1,08A + 3A battery charge 

 

*** General use 

– if the PSU is not mounted in an installation complaint with the EN-50131 standard, the 

acceptable current efficiency amounts to: 

 

 

 

 

 

  

1. Output current 5A + 0,6A battery charge 

 

 

 

  2. Output current 4,1A + 1,5A battery charge 

                                      3. Output current 3,4A + 2,2A battery charge 
                                      4. Output current 2,6A + 3A battery charge 
 

                                               Total current of the rec battery: 5,6A max. 

 

 In  case  of  power  decay,  a  battery  back-up  is  activated  immediately.  The  PSU  is  housed  in  a  metal 

enclosure  (color:  RAL  9005  -  black)  with  battery  space  for  a  65Ah/12V  battery.  It  is  fitted  with  micro  switches 
indicating unwanted door opening (front panel) and detachment from the mounting surface. 

 

 

DOPTIONAL POWER SUPPLY CONFIGURATIONS: 

(visualization available at www.pulsar.pl) 

 

1.  Buffer power supply PSBEN 13,8V/5x1A/65Ah/INTERFACE

 

              - PSBEN 5012E + LB8 5x1A (AWZ579, 65Ah+INTERFACE 

2.  Buffer power supply PSBEN 13,8V/12V/65Ah/INTERFACE 

                           - PSBEN 5012E + RN500 (13,8V/12V)+65Ah+INTERFACE 

3.  Buffer power supply PSBEN 13,8V/12V/5x1A/40Ah/INTERFACE 

              - PSBEN 5012E + RN500 (13,8V/12V)+LB8 5x1A (AWZ579, 40Ah+INTERFACE

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for PSBEN 5012E



































Reviews:

No comments

Brands by name

Popular brands

Load more brands