background image

72-910-02 
REV. P 

2

 

MICROtrac

 Warranty 

 

Pulsafeeder, Inc. warrants MICROtrac control systems (including the conductivity sensor) of its 
manufacture to be free of defects in material or workmanship.  Liability under this policy extends for 24 
months from date of shipment.  The manufacturer's liability is limited to repair or replacement of any 
failed equipment or part, which is proven defective in material or workmanship upon completion of the 
manufacturer's examination.  This warranty does not include removal or installation costs and in no event 
shall the manufacturer's liability exceed the selling price of such equipment or part. 

The manufacturer disclaims all liability for damage to its products through improper installation, 
maintenance, use, or attempts to operate such products beyond their functional capacity, intentionally or 
otherwise, or any unauthorized repair.  The manufacturer is not responsible for consequential or other 
damages, injuries, or expense incurred through the use of its products. 

The above warranty is in lieu of any other warranty, whether expressed or implied.  The manufacturer 
makes no warranty of fitness or merchantability.  No agent of ours is authorized to provide any warranty 
other than the above. 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Summary of Contents for MICROtrac























Reviews: