PTN TPUH-PSU12 User Manual Download Page 9

Page: 9 / 24

Integrated Switching Power Supply

PTN Electronics Limited 5 www.PTN-Electronics.com

4. System Connection

4.1 Usage Precaution



Verify all components and accessories included before installation.



Make sure all components and accessories included before installation.



System should be installed in a clean environment with proper temperature and
humidity.



All of the power switches, plugs, sockets, and power cords should be insulated and
safe.



All devices should be connected before power on.

4.2 System Diagram

AC100V 240V

RS232

TCP IP

24V

AC100V 240V

AC1

AC2

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

Powered Device 1

Powered Device 2

Powered Device 3

100~240VAC

RS232 Control

TCP IP Control

Power Supply

Summary of Contents for TPUH-PSU12
























Search results

Summary of Contents for TPUH-PSU12

Reviews:

Brands by name

Popular brands

PTN TPUH-PSU12, User Manual

Search results

Summary of Contents for TPUH-PSU12

Reviews:

Brands by name

Popular brands