Stator Screw
Stator
Fan Shroud
Housing
Carbon
Brush
Carbon
Brush Holder
Speed
Control
Switch
Spring
Internal
27
28
29
30
31
32
33
34
35
36
37
38
Rear Housing Screw
Cord Sleeve
Power Cord
Side Handle
Bearing Nsk688
Gear Retaining Ring
Face Gear
Gearbox Cap
Gearbox Cap Screw
Woodruff Key
Spindle
Bearing
1
2
TOOL FEATURES
TECHNICAL SPECIFICATIONS:
Technical specifications are subject to change without notice.
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance
and troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction
manual are based upon the latest product information available at the time of publication. The manufacturer
reserves the right to make product changes at any time without notice.
SAFETY GUIDELINES / DEFINITIONS
WARNING: Read and understand this entire instruction manual before attempting to assemble, install, .
operate or maintain this product. Failure to comply with the instructions may result in serious personal .
injury and/or property damage! The following signal words are used to emphasize safety
warnings that must be followed when using this product:
PARTS LIST
No. Description
No. Description
No. Description
Replacement bonnet / pad set..................................................................W50087A
REPLACEMENT PARTS AVAILABLE:
22
21
1
2
3
5
4
6
7
8
9
10
11
12
13
18
20
19
25
24
27
28
29
17
16
15
14
26
23
46
45
44
42
41
40
47
39
38
37
36
34
33
32
31
35
30
43
CAUTION: Indicates a potentially hazardous
situation that, if not avoided, MAY result in
minor or moderate injury.
NOTICE Indicates important information,
which if not followed, MAY cause damage to
equipment.
DANGER: Indicates an imminently hazardous
situation that, if not avoided, WILL result in
death or serious injury.
WARNING: Indicates a potentially hazardous
situation that, if not avoided, COULD result in
death or serious injury.
WARNING Follow all safety precautions whenever diagnosing or
servicing the tool. Disconnect power supply before service.
No-load speed: ..........................................................................2000 - 6400 RPM
Amperage: ......................................................................................................5.7A
Max accessory diameter: ...............................................................6 in. (152mm)
Spindle thread: ......................................................................................5/8 in.-11
Motor: ...............................................................................................120 V ~ 60hz
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Gearbox Cover
Screw
Screw
Screw
Gearbox
Lock Nut
Pinion Gear
Bearing
Bearing Spacer
Fan
Rotor
Magnetic Ring
Bearing
IMPORTANT SAFETY INFORMATION
1. Always use common sense and pay particular attention
to all the DANGER, WARNING, CAUTION and NOTICE
statements of this manual. The safety instructions provided
are not intended to cover all possible conditions and
practices that may occur when operating, maintaining
and cleaning power tools.
2. Observe work area conditions. Do not use machines or
power tools in damp or wet locations. Don’t expose to
rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or
liquids. Do not bring combustible materials near the tools.
Power tools create sparks, which may ignite the dust or
fumes. Keep work area clean and well lit. Cluttered work
areas invite accidents.
3. Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. as appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. the
eye protection must be capable of stopping flying
debris generated by various operations. The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or
respirator must be capable of filtering out particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
4. Keep bystanders, children and visitors away while
operating this product. Distractions can cause you
to lose control. Anyone entering the work area must
wear personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
