PT AMC123 User Manual Download Page 83

Page: 83 / 104

Front Panel Connectors

The AMC123 contains the following connectors on the front panel. See

for connector locations.

Ethernet Connectors (J1, J2)

Two RJ45 connectors on the AMC123's front panel provide two 1 Gigabit Ethernet channels.
Two bicolor LEDs are located inside each RJ45 connector:

•

Front Panel ENET Link

•

Front Panel ENET Activity

See

“LED Indicators,” on page 31

, for more information about these LEDs and

Table 5-3,

“Ethernet Connectors Pinout,”

for pin definitions.

Caution:

Insert only RJ45 plugs into the Ethernet connector. Other connectors may damage the
Ethernet connector pins.

USB Connector (J3)

A 4-pin, standard Type A USB 2.0 Port 0 Interface connector is available on the AMC123's front
panel.

Table 5-4, “USB Connector Pinout,”

shows pin definitions for this connector.

Table 5-3:

Ethernet Connectors Pinout

Pin

Signal Name

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

Table 5-4:

USB Connector Pinout

Pin

Signal Name

VCC (+5V)

USB_N

USB_P

GND

Summary of Contents for AMC123









































































































Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands

PT AMC123, User Manual

Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands