Welcome . . .
Thank you for purchasing this Delta .68 Paintball marker. The Delta .68
represents the culmination of a great deal of research by Psychoballistics along with input
from players such as you. We believe that the affordability of a reliable, feature-packed
marker will improve your playing experience and winning percentage. While winning isn’t
everything, it sure beats the alternative!
Play Hard, play safe, play to win!
WARRANTY INFORMATION
Standard Warranty:
The manufacturer warranties to the original customer that this product is free from
defects in material and workmanship under normal use and service for a period of 90
days from the original date of purchase by the initial owner/purchaser. The manufactur-
er agrees to repair or replace (at its discretion) any product within a reasonable period
of time. This warranty does not cover: o-rings, scratches, nicks, normal wear and tear of
parts, any modifications or normal fading of anodizing or damage caused by dropping or
hitting of the product. This warranty shall not apply if it is shown by the manufacturer that
the consumer caused the defect or malfunction because of misuse. This warranty only
covers original factory parts. Any modifications or tampering of original factory parts will
not be covered by this warranty. Warranty work can only be conducted by the manufac-
ture technicians and or authorized technicians. If product needs to be repaired, package
it carefully and send it together with your name, address, phone number and a brief
description of the malfunction to:
Paintball Solutions
570 Mantua Blvd
Sewell, NJ 08080
Extended Warranty:
By returning the enclosed warranty registration card or registering your warranty on-line
at www.PaintballSolutions.com, within fifteen days of purchase the warranty will auto-
matically be extended for an additional year.
Numbers shown in parentheses following part names correspond to the
numbers on the Parts key located on the centerfold pages of this manual.
Initial Assembly
1. Place a Barrel Plug into the end of the barrel. The barrel is the top chamber of the
Main Body (#23).
2. Push the safety (#25) into the “safe” position (pushing from left to right looking down
the sights).
Attaching Propellant Source
1. Confirm that the Barrel Plug is properly installed and the marker is on “Safe”.
2. Cock the marker by pulling the Bolt (#14) in the rearward direction until it “clicks”
into place. This compresses the Main Spring (#2) and allows the Cupseal (#8) to
properly seat.
3. Place a few drops of non-corrosive lubricant made specifically for use in paintball
(Empire Oil) into the center of the bottom chamber of the Main Body (#23), where the
CO2 will be punctured. This must be done for every 12 Gram CO2 put into the marker.
This will run the oil through the valve to ensure the puncture O-Rings stay moist and
do not dry or crack. Failure to do so will cause the marker to leak.
4. Place the 12 Gram CO2 cylinder into the tube with the narrow end in first.
5. Lower the clamp down so the lever is at a 45 degree angle when the plunger
makes contact with the 12 gram CO2, but doesn't puncture it (See Diagram Below). If it
doesn't touch, or touches earlier, you may have to remove the 12 gram and
screw in or back out the plunger on the front of the Gas Clamp (#19)
with your finger.
6. Point the marker downward and in a safe direction.
7. Swiftly force down the gas clamp all the way puncturing the 12g CO2
cartridge. The marker is now gassed and ready to operate.
Attaching Feed Tube
1. Confirm that the Barrel Plug is properly installed on the marker and is on “Safe”.
2. Taking the feed tube hook on the back retaining stud on the body of the Delta .68
(#23). Pulling back the front retaining stud clip into place. See Diagram below.
Installing the feed tube:
1. Hook retaining stud
2. Pull back retaining stud
and clip into place.
Removing the feed tube:
1. Pull back retaining
stud and un-clip from
the seat
2
3
D E LTA . 6 8 P A I N T B A L L M A R K E R
D E LTA . 6 8 P A I N T B A L L M A R K E R