How to set economy setpoint limit:
- Press
mode button. ECON will appear on the display.
The display will then flash room temperature and ECON.
- Press
the up arrow button. MANUAL and the default temperature
62.0°F (16.5°C) will appear on the display.
- Press
either the up or down arrow button to reach the desired
temperature. Temperature range: 40°F to 85°F (4.5°C to 29.5°C)
- Press
the mode button to complete.
To enter economy setpoint mode
:
- Press
mode button. The display will flash room temperature and
ECON.
To exit economy setpoint mode and enter comfort setpoint mode:
- Press
mode button. The display will show only room temperature.
How to change from °F to °C:
- Press
and hold the mode and down arrow buttons. The display
will change to °C from the default of °F. To change back, simply
press and hold the buttons again.
Stop/On Mode:
While in normal operating mode, the slide switch should be in the
On
position. While in the
On
mode the thermostat will be active until the
desired setpoint is reached.
When slide switch is in the
Stop
position the thermostat will not call
for heating unless the temperature drops below 40°F (5°C). At this
time the thermostat will be active until the temperature reaches 40°F.
This mode may be useful to prevent pipes freezing while on vacation,
etc.
Memory Retention:
When the power goes off the current parameters will be saved and
then restored when power returns.
PSG Controls, Inc.
LIMITED WARRANTY POLICY
PSG Controls, Inc. (Hereinafter referred to as "PSG") warrants the following:
Only cataloged products sold to distributors are warranted to the original purchaser, to
conform with specifications furnished or approved by PSG, and to be free from defects in
material and workmanship, for a period of one (1) year from the date of purchase, unless
specified in writing for a different period.
Any PSG product that proves defective within the above described warranty period will
be repaired or replaced (at PSG's option) free of any charge if returned to the PSG
factory at 1225 Tunnel Road, Perkasie, PA. 18944 with transportation charges prepaid.
Prior to returning this product to PSG, the purchaser shall give PSG notice in writing
stating how this product fails to fulfill this warranty. No product shall be accepted for
repair or replacement without a required written notice and without prior written
authorization and shipping instructions having been received by the purchaser from
PSG. Only PSG's factory is authorized to perform services under this warranty.
This warranty does not extend to any product that has been subjected to misuse, abuse,
neglect, accidents, alterations, improper installation or use in violation of the printed
instructions furnished by PSG. This warranty neither applies to batteries nor
deterioration of, nor damage to the product caused by the use of faulty batteries. Final
determination as to whether any product is actually defective rests solely with PSG.
This warranty is expressly in lieu of all other agreements and warranties, expressed,
implied, or statutory and PSG has no other obligations or liabilities in connection with this
product. In no event shall PSG's obligation or liability hereunder exceed the purchase
price of this product. PSG SHALL NOT IN ANY EVENT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty gives you specific legal
rights, and you also have other rights which vary from state to state. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or implied
warranties, so the above limitations or exclusion may not apply to you.
Toll free technical assistance is available
via our technical hotline: 1-800-523-2558
Mon-Fri, 8:00 A.M. to 4:30 P.M. Eastern Standard Time
1225 Tunnel Road - Perkasie, PA 18944 - 215-257-3621 - Fax 215-257-4288
Web site - www.psgcontrols.com E-mail - [email protected]
R
PSG Controls, Inc.
Adjusting Comfort
Setpoint:
(For Installation Test)
How to program heating limit:
Press up arrow button to increase temperature
Press down arrow button to decrease temperature
Thermostat will automatically return to room
temperature display within 30 seconds
Heat will become active if new setpoint is above room
temperature. Heat icon ( ) will indicate that the thermostat
is calling for heat.
The heating limit is the maximum room temperature the thermostat
will allow even if the setpoint is higher.
Programmable Range: 40.0°F to 85.0°F (4.5°C to 29.5°C)
The programming mode has a time limit of 5 minutes. The timer is
automatically activated on initiation of the programming mode. At the
end of 5 minutes the thermostat will resume normal operation.
To enter the programming mode:
- Slide
the STOP/ON switch to the STOP position.
- Press
and hold the up arrow button and programming mode button
for 5 seconds. 00 will appear on the display.
- Press
the up arrow button to access code
21
.
- Press
the mode button. The default temperature of 85.0°F
(29.5°C) will appear on the display.
- Press
either the up or down arrow button to reach the desired
temperature.
- Press
the mode button to complete.
- Slide
the STOP/ON switch back to the ON position to resume
normal
operation.
Standard
Junction
Box
o
F
Stop/On
Mode
75.2
AUTO
SU
LEAVE
User Note: The top of this unit will become warm to the
touch. This is a normal operation. Internal heating is
employed to continuously convect air through the
thermostat, thereby improving room air temperature
measurement.
Mounting Detail
