background image

R

ETURN

 

TO

 F

ACTORY

 C

ONFIGURATION

If, during a programming session, you wish to reset the scanner's con-
figuration to its original factory settings, scan the RETURN TO FACTORY
SETTINGS label below.  Use this label ONLY IF NECESSARY, since it will
reset any changes made to this interface during any previous program-
ming session.

RETURN TO FACTORY SETTINGS

NOTE

P

ROGRAMMING

 M

ODE

The scanner must be placed in Programming Mode before its configura-
tion can be altered using the barcodes in this guide. Enter Programming
Mode by scanning the START label found at the bottom of each page.
The scanner's green light will flash continuously, indicating the scanner is
in Programming Mode.

While in Programming Mode, the scanner will recognize only specially
formatted programming barcode labels like those contained in this guide,
and will not decode barcode labels of any other type.  Scan all program-
ming barcode labels needed to set the scanner's features to the desired
settings.  The scanner will beep after each barcode label is scanned, indi-
cating that the setting has been stored in memory.  The scanner will emit
a rejection tone if a scanned barcode programming label isn't valid.
To exit Programming Mode and save all changes made during the pro-
gramming session, scan the END label located at the bottom of each
page.  The scanner will return to normal operation.

Disconnecting power during Programming Mode will cause the scanner
to return to its previous settings.

2

QuickScan 6000/6000 PLus Universal Wedge Interface Programming

*/+$*

When this feature is scanned, return to factory set-
tings will take about five seconds to complete.  The
scanner will sound a tone at its conclusion.

Summary of Contents for QuickScan 6000









Reviews: