background image

1

Smart Gate Series

Rev022520

© 2020 PS Industries

®

 Incorporated. All Rights Reserved.

IMPORTANT! 

Read entire Instruction and Operations Manual to become familiar with the product.

NOTICE

 

This product is a fall protection product. The effectiveness of the product is directly related to the proper 

installation and operation of this product. Failure to properly maintain this product 

will

 

affect performance.

Publication Notice

This manual has been compiled and published covering the latest product descriptions and specifications.

The contents of this manual and the specifications of this product are subject to change without notice.

 

PS Safety Access™ reserves the right to make changes without notice in the specifications and materials contained 

herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials 

presented, including but not limited to typographical and other errors relating to the publication.

PS Safety Access and/or its respective suppliers may make improvements and/or changes in the product(s)/ 

service(s) offered and/or the program(s) at any time without notice.

Retain this manual for future reference.

If you would like to download a copy of this manual, please go to pssafetyaccess.com

Product registration is an essential step to protecting your product, register Online at 

psindustries.com/contact/register-your-product/

PN 514186 B

Installation Instructions/Operation and Maintenance Manual

Patent Pending

Table of Contents:

Safety Precautions ............................................................. 2

Product Information ........................................................... 2

Installation Instructions ..................................................... 4

Disassembling of Gate .....................................................12

Operation ..........................................................................13

Replacement Parts List ...................................................14

Size Reference Drawing

 ...................................................15

Inspection and Maintenance...........................................16 

Warranty Certificate

 .........................................................19

Models: 

 SG-96-PCY 

 *

Refer to page 15 for required size dimensions.

Contact Information

Mail

PS Safety Access

1150 South 48th Street

Grand Forks, ND 58201

Website

pssafetyaccess.com

Email

[email protected]

Local Phone

701.746.4519

Toll Free Phone

877.446.1519

Hours of Operation

8 A.M. to 5 P.M. CT

Monday – Friday

Summary of Contents for EDGESAFE Smart Gate





















Reviews: