PS Engineering PMA7000BT System Installation And Operation Manual Download Page 29

PS Engineering

PMA7000BT Audio Selector Panel and Intercom System

Installation and Operator’s Manual

200-780-0204

Page 4-1

Rev. 1, July 2015

Section IV- Warranty and Service

4.1

Warranty

In order for the factory warranty to be valid, the installations in a certified aircraft must be accomplished by
an FAA-(or other ICAO agency) certified avionics shop and authorized PS Engineering dealer.  If the unit
is being installed by a non-certified individual in an experimental aircraft, a factory-made intercom harness
must be used for the warranty to be valid.

PS Engineering, Inc. warrants this product to be free from defect in material and workmanship for a period
of two (2) years from the date of purchase. During the first twelve (12) months of the two-year warranty
period, PS Engineering, Inc., at its option, will send a replacement unit at our expense if the unit should be
determined  to  be  defective  after  consultation  with  a  factory  technician.  For  the  remaining twelve (12)
months 
of the two-year warranty period, the unit must be returned to PS Engineering, Inc., or an authorized
warranty service facility, for no-cost repair.

All transportation charges for returning the defective  units  are the responsibility of the purchaser. All do-
mestic transportation charges for returning the exchange or repaired unit to the purchaser will be borne by
PS Engineering, Inc. The risk of loss or damage to the product is borne by the party making the shipment,
unless the purchaser requests a specific method of shipment. In this case, the purchaser assumes the risk of
loss.

This warranty is not transferable. Any implied warranties expire at the expiration date of this warranty. PS
Engineering  SHALL  NOT  BE  LIABLE  FOR  INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES.  This
warranty does not cover a defect that has resulted from improper handling, storage or preservation, or un-
reasonable use or maintenance as determined by us. This warranty is void if there is any attempt to dissem-
ble this product without factory authorization. This  warranty gives you specific legal rights, and you may
also have other rights, which may vary from state to state. Some states do not allow the exclusion of limita-
tion of incidental or consequential damages, so the above limitation or exclusions may not apply to you.

All items repaired or replaced under this warranty are warranted for the remainder of the original warranty
period.  PS  Engineering,  Inc.  reserves  the  rights  to  make  modifications  or  improvements  to  the  product
without obligation to perform like modifications or improvements to previously manufactured products.

4.2

Factory Service

The units are covered by a two-year limited warranty. See warranty information. Call PS Engineering, Inc.
at (865) 988-9800 before you return any unit. This  will allow the service technician to  provide any other
suggestions for identifying the problem and recommend possible solutions.

After  discussing  the  problem  with  the technician  and  you  obtain  a  Return  Authorization  Number,  ship
product to:

PS Engineering, Inc.
Attn: Service Department
9800 Martel Rd
Lenoir City, TN 37772
(865) 988-9800

FAX (865) 988-6619

Email: [email protected]

Units that arrive without an RMA number, or telephone number for a responsible contact, will be
returned un-repaired. PS Engineering is not responsible for items sent via US Mail.

Summary of Contents for PMA7000BT



































Reviews: