Proximus forum 523 Mounting And Commissioning Manual Download Page 65

Page: 65 / 228

Brief Guide to Initial Configuration

Configuration

Note:

The Forum 523/524’s IP address is always 192.168.99.254 in
its factory settings (see

LAN Settings / Internet Functions

starting on page 24).

Brief Guide to Initial Configuration

Setting up a first connection is quite simple with a standard Windows PC:

Connect the PC’s network card with one of the Forum 523/524.’s LAN
ports You can use a crossed or an uncrossed Ethernet cable to do this.

If the DHCP automatic configuration is functioning, it is possible to
continue with step 6.

Log on as a user with “Administrator” rights.

Setting the IP address in Windows

You will find the IP settings in Windows under

Control Panel

Network

and Sharing Center

Change adapter settings

(Windows 8) or under

Start

Settings

Network connections

Local Area Connection

. Open the

dialogue box

Local Area Connection / Ethernet Properties

, and then the

dialogue box

Internet Protocol Version 4 Properties

Note down the existing settings so that you can restore them after
completing the initial configuration.

Summary of Contents for forum 523





































































































































































































































Search results

Summary of Contents for forum 523

Reviews:

Related manuals for forum 523

Brands by name

Popular brands

Proximus forum 523, Mounting And Commissioning Manual

Search results

Summary of Contents for forum 523

Reviews:

Related manuals for forum 523

Brands by name

Popular brands