Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 67 | Manualshive

Page: 67 / 348

Proximus Forum 500 Series Mounting And Commissioning Manual Download Page 67

Signalling and Audio Channels

Forum 5004/5008/5012 and Gateways

65

The call server of the Forum 5004/5008/5012 communications system and
all connected gateways must be operated on a LAN. Lossless data transfer
with low latency and 100 Mbit/s is the prerequisite for interference-free
telephony. To ensure data transfer you should use suitable network
technology, e.g. a switch with QoS, an own VLAN or wiring separate from the
company LAN.

Routers can also be used to connect the call server of the Forum 5004/
5008/5012 communications system and the gateways connected. Using the
web interface of the gateway you have to define a fixed IP address and the
standard gateway to be used (see

Operating a Gateway via Router

on page 69). Please note that due to unencrypted communication and the
speed requirements a connection via internet is not supported.

Tip:

For connecting distant locations, use the telecommunications
system networking options (see

PBX Networking

Signalling and Audio Channels

Each hardware unit has an audio processor (Forum 5012: 2 audio processors).
The audio processor provides multiple VoIP audio channels implemented as
RTP data stream with the G.711 or G.729 codecs. The following applies
generally: Each audio connection which leaves the hardware unit via a VoIP
connection requires an audio channel.

TDM and VoIP gateway connections

VoIP

TDM

TDM

«
...
65
66
67
68
69
...
»

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands