manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

The Proximus Forum 500 Series is a cutting-edge communication device that revolutionizes business collaborations. Enhance your productivity with this sleek and efficient technology. To maximize its potential, don't forget to download the free user manual from manualshive.com. Discover the endless possibilities this device has to offer.

Share
Download
background image

Forum Gateway 560 Connection via PCM-V Connection

133

Forum Gateway 560 Connection via 
PCM-V Connection

All VoIP audio connections that originate with a Forum Gateway 560 and go 
to the Forum 5004/5008/5012 communications system (Call Server) are 
conducted via the RTP protocol and require one media gateway channel 
respectively. Audio tones, recording music on hold and also what is required 
for generating DTMF tones are controlled by the call server; each of these 
briefly seizes a media gateway channel. This is why a Forum Gateway 560 
needs to be suitably equipped with a corresponding number of media 
gateway cards depending on the number of connected terminals and the 
level of expected audio traffic. 

Media gateway channels can, however, be also seized in a second, 
neighbouring Forum Gateway 560. This requires that both 
Forum Gateways 560 are connected to one another via a PCM-V line. The 
PCM-V line transports both voice as well as administration data between the 
Forum Gateways 560. Connecting the Forum Gateways 560 also makes it 
possible to optimise the required number of media gateway cards. 

Note:

The central control modules of both Forum Gateways 560 
must respectively have their own Compact Flash card for saving 
the operating software.

Installation Steps

The following installation steps described are necessary in order to connect 
Forum Gateways 560.

DANGER!

Hazardous voltages inside the device!

1.

Disconnect both Forum Gateways 560 from the power supply. If you are 
using two power supplies for a Forum Gateway 560, you must unplug 

both

 power supplies of the Forum Gateway 560!

2.

One of the Forum Gateways 560 assumes the PCM master role. The other 
Forum Gateway 560 is the PCM slave. The Forum 5004/5008/5012 
communications system detects the Forum Gateway 560 function as PCM 
master or as PCM slave via the frame number. The frame number of a 

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for Forum 500 Series

GE PACSystems RX7i Reference Manual preview
PACSystems RX7i
Brand: GE Pages: 317
Accutrol VTS Installation & Operation Manual preview
VTS
Brand: Accutrol Pages: 25
Jäger ADwin-Gold Hardware Manual preview
ADwin-Gold
Brand: Jäger Pages: 50
OBSIDIAN CONTROL SYSTEMS NX1 Installation Manual preview
NX1
Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13
Zeck Audio VECTOR S3A Owner'S Manual preview
VECTOR S3A
Brand: Zeck Audio Pages: 16
OBSIDIAN CONTROL SYSTEMS NX2 Installation Manual preview
NX2
Brand: OBSIDIAN CONTROL SYSTEMS Pages: 16
D&R ELECTRONICS RDS17S-ELITE1-R1 Installation Manual preview
RDS17S-ELITE1-R1
Brand: D&R ELECTRONICS Pages: 12
Alpine MRA-355 Manual preview
MRA-355
Brand: Alpine Pages: 16
Vestil BOL-R Series Instruction Manual preview
BOL-R Series
Brand: Vestil Pages: 6
Lucent Technologies MERLIN LEGEND Release 7.0 System Programming Manual preview
MERLIN LEGEND Release 7.0
Brand: Lucent Technologies Pages: 1082
Stahl 8146/5 Series Operating Instructions Manual preview
8146/5 Series
Brand: Stahl Pages: 24
Aiwa CX-JE3 Service Manual preview
CX-JE3
Brand: Aiwa Pages: 68
JL Audio Stealthbox SB-GM-4GSUVCNSL/10TW1 Installation Manual preview
Stealthbox SB-GM-4GSUVCNSL/10TW1
Brand: JL Audio Pages: 7
Technics st-ch510 Service Manual preview
st-ch510
Brand: Technics Pages: 14
RAM CSS205 User Manual preview
CSS205
Brand: RAM Pages: 36
FAAC J355HA M50 Translation Of The Original Instructions preview
J355HA M50
Brand: FAAC Pages: 16
Daewoo AMI-225M Service Manual preview
AMI-225M
Brand: Daewoo Pages: 29
Work Pro Roader 408 User Manual preview
Roader 408
Brand: Work Pro Pages: 12

Brands by name

Popular brands

Load more brands