Protrol IPC4020 User Manual Download

Page: 18 / 63

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

e-mail: [email protected]

6.1 Device Settings

– Unit

The IPC device has general settings on the

Unit

subtab, listed in the table beneath. The

Watchdog

relay

closes when all is normal. If there is an internal fault, the relay opens. If power supply is missing, the relay
will remain open.

Parameter

Description

Range

Factory value

Unit

Unit information:

Site

Site reference

Default

FreeText

Free text for extra information

Wathdog output:

Enable

Activation of the Wathdog feature

Yes or No

Watchdog relay

Choice of relay output

1..8

PDCIO:

Enable

Activation of external I/O-module PDCIO

Yes or No

6.2 Time synchronisation

– NTP

IPC402x has support for time synchronization using NTP. Settings can be found on the

Config/NTP

tab.

Figure 7.

Configuration of NTP.

If the disturbance recording files shall be visualized using Protrol-Tool, the station name is not allowed to have

spaces. Alternatively, the files must be edited before they can be loaded by the tool.

PDCIO is described in details in its own user’s man

ual [4].

Summary of Contents for IPC4020
































































Search results

Summary of Contents for IPC4020

Reviews:

Related manuals for IPC4020

Brands by name

Popular brands

Protrol IPC4020, User Manual

Search results

Summary of Contents for IPC4020

Reviews:

Related manuals for IPC4020

Brands by name

Popular brands