ENGLISH
4
Fig. C
Fig. D
Wall Mounting (Fig. E)
This charging dock
13
is designed to be wall mountable or
to sit flat on a table or work surface. If wall mounting, locate
the charger within reach of an electrical outlet, and away from
a corner or other obstructions which may impede air flow.
Use the back of the charger as a template for the location of
the mounting screws on the wall. Mount the charging dock
securely using drywall screws (purchased separately) at least
1" (25.4 mm) long, with a screw head diameter of 0.28–0.35"
(7–9 mm), screwed into wood to an optimal depth leaving
approximately 7/32" (5.5 mm) of the screw exposed. Align
the slots on the back of the charging dock with the exposed
screws and fully engage them in the slots.
13
Fig. E
2" (50 mm)
1-9/16" (40 mm)
2-11/16"
(68 mm)
Charger Cleaning Instructions
!
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained
if the battery is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery below +40 °F (+4.5 °C), or above +104 °F
(+40 °C). This is important and will prevent serious
damage to the battery.
2. The charger and battery may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery after use, avoid placing the charger or the
wrench in a warm environment such as in a metal shed
or an uninsulated trailer.
3. If the wrench does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other wrench;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. Move the charger and tool to a location where
the surrounding air temperature is approximately
65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, and
charger to your local service center.
4. The battery should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with
no adverse effect on the battery.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no tool in the cavity. Unplug the charger before
attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery in a cool dry place out of the charger for
optimal results.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Intended Use
This manually operated torque wrench is used to apply a
specific torque value to a fastener, such as a nut or bolt.
DO NOT
use under wet conditions or in presence of
flammable liquids or gases.
This manually operated torque wrench is a professional
hand tool.
DO NOT
let children come into contact with the
tool. Supervision is required when inexperienced operators
use this tool.
BLE communication and APP control gives access to
additional functionality such as fast setting, programming
sequences and data recording.
Summary of Contents for J6110BT
Page 27: ......
