background image

AC040  is  a  guided-type  fall  arrester  device  sliding  on  a 

 

ø

12 mm rope. AC040 is a component of the personal fall 

arrest equipment  and complies with EN353-2.
The device is a protection for the one person only.

!

rope grab is made of stainless steel. It could be used only 
with ropes of diameter 12 mm.

!

working  rope  (

ø

12  mm  polyester  kernmantle  rope). 

The endings of the rope are equipped with the loops with 
plastic thimble.

BASIC EQUIPMENT

working rope 

ø

12

 mm

working rope identity label

top end 
of the working rope
(the loop with the thimble)

rope grab

bottom end 
of the working rope
(the loop with the thimble)

GUIDED-TYPE  FALL  ARRESTER
ON FLEXIBLE ANCHORAGE LINE 

Rope grab ref. number: AC 040

Instruction Manual

READ CAREFULLY BEFORE USE 

THE EQUIPMENT

AC 040

Working rope ref. number: AC 200 XX

EN 353-2:2002

AC 200 XX*

WORKING ROPE

EN 353-2:2002

Date of manufacture: 02.2018

Serial number: 00001

LENGTH: XX m

POLYESTER

DIAMETER: 

ø12 mm

  1. 
  2. reference number
  3. European standard (number/year).
  4. CE marking and number of a notified body controlling 

manufacturing of the equipment (art. 11).

  5. year of manufacture.
  6. number of manufacturing serie.

name (type) of the device.

  7. caution: read the manual
  8. marking of device manufacturer of distributor.
  9. material of which the device is made of.
10. diameter of the rope.
11. length of the rope.

1

2

9

10
11

5
6
3
4

8

*) xx - code of length 
    for example: xx=03 - length 3 m
                         xx=20 - length 20 m

EN 353-2:2002

Date
of manufacture: 2018

USE
ONLY WITH ROPES 
OF DIAMETER  

ø1

2 mm

Serial
number: 00001

GUIDED-TYPE FALL ARRESTER
 

Ref. AC 040

MARKING

1

2

5

6

3

4

8

7

!

personal protective equipment must be withdrawn from use immediately when 
used again until confirmed in writing by equipment manufacturer or his representative after carried out the detailed inspection.

!

personal protective equipment must be withdrawn from use immediately and destroyed  when it have been used to arrest a fall.

,

!

a full body harness is the only acceptable body holding device that can be used  in a fall arrest system.

!

in full body harness use only attaching points marked with big letter "A" to attach a fall arrest system. 

!

the anchor device or anchor point for the fall arrest system should always be positioned, and the work carried out in such a way, as to 
minimise both the potential for falls and potential fall distance. The anchor device/point should be placed above the position of the user 
. The shape and construction of  the anchor device/point shall not allowed to self-acting disconnection of the equipment. Minimal static 
strength of the anchor device/point is 15 kN. It is recommended to use certified and marked structural anchor point complied with 
EN795.

!

it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system, so 
that, in the case of a fall, there will be no collision with the ground or other obstacle in the fall path. The required value of the free space 
should be taken from instruction manual of used equipment.

!

there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be 
observed during equipment utilization, especially:
- trailing or looping of lanyards or lifelines over sharp edges; 

-  any defects like cutting, abrasion, corrosion;       - climatic 

exposure;  
- pendulum falls;

   - extremes of temperature;

      - chemical reagents; 

             - electrical conductivity.

!

personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made 
of steel or plastic) to protect it against damage or moisture.

!

the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products 
use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. 
When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry naturally, and shall be kept 
away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure 
better operation. 
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.

!

personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet 
degradation, damp environment, sharp edges, extreme temperatures and corrosive or aggressive substances.

any doubt arise about its condition for safe use and not 

connector 

of the rope grab

SafetyLiftinGear.com
Unit R1D Rockingham Gate Poplar Way
West Cabot Park Bristol BS11 0YW
Tel: 0808 123 69 69 Fax: 0117 9381 602
[email protected]

Notified body, at which the European certification was Iissued 
and which supervises the production of the equipment: 
APAVE SUDEUROPE SAS - 8 rue Jean-Jacques Vernazza - 
CS-60193 – 13322 MARSEILLE Cedex 16, France - No. 0082 
PRODUCENT: PROTEKT, 93-403 LODZ, ul. Starorudzka 9, POLAND, 
TEL:  (48 42) 680 20 83, FAX: (48 42) 680 20 93, www.protekt.com.pl

PERIODIC INSPECTIONS 

The device must be inspected at least once every 12 months from 
the date of first use. Periodic inspections must only be carried out by 
a competent person who has the knowledge and training required 
for personal protective equipment periodic inspections. Depending 
upon the type and environment of work, inspections may be needed 
to be carried out more frequently than once every 12 months. Every 
periodic inspection must be recorded in the Identity Card of the 
equipment. 

MAXIMUM LIFESPAN OF THE EQUIPMENT 

The maximum lifespan of the device is 10 years from the date of 
manufacture. The device must be withdrawn from use immediately 
and destroyed when it has been used to arrest a fall or it fails to pass 
inspection or there are any doubt as to its reliability.
 

ATTENTION:

 The lifetime of the device depends on the intensity of 

usage  and  the  environment  of  use.  Using  the  device  in  rough 
environment,  marine  environment,  contact  with  sharp  edges, 
exposure to extreme temperatures or agressive substances, etc. can 
lead to the wthdrawal from use even after one use.

Summary of Contents for AC 040

Page 1: ...al of used equipment there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization especially trailing or looping of lanyards or lifelines over sharp edges any defects like cutting abrasion corrosion climatic exposure pendulum falls extremes of temperature chemical reagents electrical conductivity ...

Page 2: ...l condition that could affect the safety of the equipment user in normal and emergency use a rescue plan shall be in place to deal with any emergencies that could arise during the work it is forbidden to make any alterations or additions to the equipment without the manufacturer s prior written consent any repair shall only be carried out by equipment manufacturer or his certified representative p...

Page 3: ...A COMPETENT PERSON RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS REPAIRS REASONS OF EQUIPMENT S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD ALL RECORDS I...

Page 4: ...THE FIRST USE BY A COMPETENT PERSON RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS REPAIRS REASONS OF EQUIPMENT S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY C...

Reviews: