PT-5203A/I/G
Electric Engraver
1. 0n/off switch 2. Engraving tip 3.Stroke adjustment dial
4. Tip release screw 5.Power cord 6.LED light
CAUTION
！
Thoroughly read and understand all instructions before using
this product. Indicates operating time at no more than 30
minutes at rated load followed by a complete cool down of the
tool.
Specifications
：
Consumption
：
10W
Input Voltage
：
PT-5203A
：
AC 120V 60Hz
PT-5203I
：
AC 220~240V 50Hz
PT-5203G
：
AC 220~240V 50Hz
Speed
：
7,100 spm
Stroke setting
：
9 Position
Engraver point holder
：
Φ
3.0 mm
Engraving bit
：
Tungsten Carbide Tipped steel
GENERAL SAFETY INSTRUCTIONS
WARNING
！
Read all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and /or serious injury.
1) ELECTRICAL
SAFETY
a)
Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c)
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep the cord away from heat, oil and sharp
edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
e) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
2) PERSONAL SAFETY
a) Stay alert Watch what you are doing and use common sense when
operating a power tool. Do not operate tool when you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hardhat, or ear protection used
for appropriate conditions will reduce personal injuries.
c)
Avoid accidental starting. Ensure the switch is in the off position before
plugging in. Carrying power tools with your finger on the switch or plugging
in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f)
Dress appropriately. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
3)
POWER TOOL USE AND CARE
a)
Do not force the tool. Use the correct power tool for your application, The
correct power tools will do the job better and safer at the rate for which
they were designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c)
Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Maintain power tools, Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
e) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
f) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for that particular type of
power tool, taking into account the working conditions and the work to be
performed. Use of the power tool for operations other than those intended
could result in a hazardous situation.
4) SERVICE
a) Have your power tool serviced by a qualified technician using only identical
replacement parts. This will ensure that the safety of the power tool is
maintained.
ADDITIONAL SAFETY INSTRUCTIONS FOR ENGRAVERS
• Always wear eye, ear and breathing protection
• Do not apply too much pressure when engraving
WARNING
！
The use of an accessory or attachment other than those
recommended in this Instruction Manual, may present a risk of personal injury.
To use this tool properly, you must observe the safety regulations, the
assembly instructions and the operating instructions to be found in this Manual.
All persons who use and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards. Children and
intirmed people must not use this tool. Children should be supervised at all
times if they are in the area in which the tool is being used. It is also imperative
that you observe the accident prevention regulations in force in your area. The
same applies for general rules of occupational health and safety.
6
The manufacturer shall not be liable for any changes made to the tool nor for
any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible to eliminate all
residual risk factors. The following hazards may arise in connection with the
tool's construction and design
：
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective earmuffs are not worn.
• Damage to eyes if effective goggles are not worn.
• Risk of injury unless hands are kept well clear of cutting devices.
I
NSTALLING AN ENGRAVER TIP
WARNING
！
Disconnect the engraver from the power supply before
making any adjustments or maintenance procedures.
1. Loosen the tip release screw (4) by turning it anticlockwise with a flat head
screwdriver.
2. To fit the new engraving tip (2), insert the tip through the centre of the hole of
the engraver, ensuring the tip fully enters the housing. A new tip should
protrude from the end of the housing by approximately 8.5mm.
3. Tighten the tip release screw (4) fully by rotating in a clockwise direction.
OPERATION
WARNING
！
Always wear safety glasses when using this tool.
The engraver can be used to permanently mark metal, glass, plastic, wood,
ceramics and much more.
1. Before using the engraver you must ensure there is an engraving tip
installed.
2. Connect the engraver plug to the power supply and while holding the
engraver firmly, push up on the on/ off switch (1) with your thumb.
NOTE
！
To turn the tool on, press the small On/Off Switch (1) upwards
to the (I) position. To turn the tool off, push the on/off Switch (1) down
to the (O) position.
3. Hold the engraver at an angle like you would hold a pen. Do not press down
hard while engraving, use light pressure while guiding the point over the
work to be completed.
ADJUSTING THE DEPTH OF ENGRAVING
1. The stroke adjustment dial (3) located on the side of the engraver controls
the stroke length and therefore the depth of engraving.
2. For a fine mark turn the stroke adjustment dial (3) anticlockwise to position
“1”.
3. For a deeper, thicker mark turn the stroke adjustment dial (3) clockwise to
position “5”
NOTE
！
It is recommended that you practice on scrap material before
you start.
MAINTENANCE
WARNING
！
Always ensure that the tool is switched off and the plug is
removed from the power point before making any adjustments or
maintenance procedures.
1. Use a soft brush to remove any accumulated dust. Wear safety glasses to
protect your eyes whilst cleaning.
2. If the body of the tool needs cleaning, wipe it with a soft damp cloth. A mild
detergent can be used but never alcohol, petrol or other harsh cleaning agents.
3. Never use caustic agents to clean plastic parts.
CAUTION
！
Water must never come into contact with the tool.
General inspection
Regularly check that all the fixing screws are tight. They may vibrate loose over
time.
