background image

FIRST TIME USE

●Remove and discard the insulation tab as figure on the right.

●Replacing Batteries For Remote Control

1. Push and slide out the battery holder as figure 1 below.

2. Replace the battery with a new CR2025 button cell as the polarity

markings on the rear of the Remote Control.

3. Close the battery holder.

BATTERY PRECAUTIONS

Follow these precautions when using a battery in this device:

1. Use only the size and type of battery specified.

2. Be sure to follow the correct polarity when installing the battery as indicated

in the battery compartment, a reserved battery may cause damage to the device.

3. Do not mix different types of batteries together ( e.g: Alkaline and Carbon -zinc )

or old batteries with fresh ones.

4. If the batteries in the device are consumed or the device is not to be used for a long

period of time, remove the batteries to prevent damage or injury from possible

leakage.

5. Do not try to recharge the battery not intended to be recharged; it can overheat

and rupture. ( Follow battery manufacturer’s instructions.)

6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

7. Clean the battery contacts and also those of the device prior to battery installation.
8. The remote control supplied with a coin/button

cell battery. If the coin button cell battery is

swallowed, it can cause severe internal burns in

just 2 hours and can lead to death. Keep new

and used battery away from children. If the

Battery compartment does not close securely,

stop using the product and keep it away from

children. If you think batteries might have been

swallowed or placed any part of the body, seek

immediate medical attention.

CR2025

Fig.1

Fig.2

Fig.3

BATTERY  INSTALLATION  OF  REMOTE CONTROL

Remote control operation range

●When there is an obstacle between the remote and the transmitter, the unit may not

operate.

●When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light

shines on the REMOTE SENSOR of the unit, the operation of the remote may be

unstable.

CAUTION

●Danger of explosion if the battery is incorrectly replaced.

●Replace only with the same or equivalent type.

9

Summary of Contents for PSB3200-FD-PL

















Reviews: