ProScan PRD8630A User Manual Download Page 62

Page: 62 / 84

Reference

Controls and Buttons

This part of the Reference sections discusses the controls and
buttons located on the receiver and the remote control.

Front Panel Controls

ON/OFF Turns the DSS

receiver’s power on or off.

DISPLAY Brings up the on-screen channel marker.

ANTENNA Switches the source of the video signal from
DSS

satellite signals to an off-air antenna or cable signal.

ARROWS Press the navigation arrows to move the on-screen
highlight up, down, left, or right. Using the arrows to
highlight a menu item is also called “pointing.”

MENU•SELECT Brings up the Main menu. If you are
already in the menu system, press MENU•SELECT to select a
highlighted choice.

ACCESS CARD Identifies you to your program providers.
The DSS

system requires a valid access card.

The Access Card door slides open so that you can replace the card when necessary.

ON/OFF

DISPLAY

ANTENNA

SELECT

Summary of Contents for PRD8630A





















































































Search results

Summary of Contents for PRD8630A

Reviews:

Related manuals for PRD8630A

Brands by name

Popular brands

ProScan PRD8630A, User Manual

Search results

Summary of Contents for PRD8630A

Reviews:

Related manuals for PRD8630A

Brands by name

Popular brands