background image

2. Bracket, Bolt, and Plate Assembly 

Assemble as shown below using the 5/16 Button Head Screw. Make certain the threaded barrel on clip is 

facing downward. 

 

 

          

            

     

          

     

 

 

      

 

   

        

              

    

   

         

           

 

  

   

         

 

 

   

     

  

    

 

 

 

3. Insert Assembly into Stake Pocket Hole 

 

Insert the assembly in to the stake pocket hole by positioning the plate with threaded clip into the stake pocket hole.  

 

ProRac Systems Inc.                                                                                                                                                               Toll Free: 1-800-217-7133 

1800 Freeway Blvd                                                                                                                                                                  Phone: 763-546-5620 

Minneapolis, MN 55430-1708                                                                                                                                                  Fax: 763-546-0933 

                                                                                                                Page 2 of 3                                                               WWW.PRORAC.COM 

Summary of Contents for TONNEAU









Reviews: