promethean Activesound One Instruction Manual Download Page 41

 

41 

Safety Instructions for 

European Countries  

Power disconnection. Unit with or without ON-OFF switches have power 
supplied to the unit whenever the power cord is inserted into the power 
source; however, the unit is operational only when the ON-OFF switch is 
in the ON position. Unplug the power cord to disconnect the main power 
for all units.   

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT 
CAREFULLY 

This appliance is supplied with a moulded three pin mains plug for your 
safety and convenience. A 13 amp (CAE-100W) and 3 amp (CAE-50W, 
CAE-20W, RC-07) fuse is fitted in this mains plug. Shall the fuse need to be 
replaced, please ensure that the replacement fuse has a rating of 13 amp 
(CAE-100W) and 3 amp (CAE-50W, CAE-20W, RC-07, BD09)and the it is 
approved by ASTA or BSI 

to 

BS1362. 

 
 
Check for the ASTA mark or the BSI mark on the body of the fuse. If the 
plug contains a removable fuse cover you must ensure that it is refitted when 
the fuse is replaced. If you lose the fuse cover, the plug must not be used 
until a replacement cover is obtained.  
 

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE 
SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE 
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF 
SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL 
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP 
SOCKET.  

If a new plug is to be fitted please observe the wiring code as shown below. 
If in any doubt, please consult a qualified electrician.  

WARNING: This apparatus must be earthed. 

IMPORTANT 

The wires in this mains lead are coloured in accordance with the following 
code: 
  Green 

and 

yellow: Earth 

 

 

Blue: 

 

 

Neutral 

 

 

Brown:   

 

Live 

As the colours of the wire in the mains lead of this appliance may not corre-
spond with the coloured markings identifying the terminals in your plug, 
proceed as follows.  
 

Summary of Contents for Activesound One













































Reviews: