background image

 

 

 

Power Supply Function : 

 

The built-in 5V USB Port 

 

enables the PROMASTER

®

 XtraPower Tr charger to  work as a 5V USB Power Supply 

capable of pow ering and charging many  por table electronic devices -- such as  MP3/MP4 Play er, PDA, Mobile Phone, 

GPS …etc. 

 

 

To Work as a 5V USB Power Supply

Cell 

Phone

PDA 

    Smart 

Digital 

Camera

 

USB Connecting Cable 

(Comes with your device) 

Gaming 

Device

 

MP3/MP4 

Device 

GPS

 

 

 

Note: The 5V USB Pow er Port of the Traveler  + charger works only AFTER the battery  being charged at the battery  

port is fully charged (Its LED turns green) or when there is no battery being charged at the battery port of this charger.  

It is not possible to charge a battery and use USB power simultaneously. 

 

IMPORTANT NOTES:   

1.  All batteries w ill naturally  discharge themselves even if t

hey are not in use. To prolong their service 

life,  it  is 

recommended that you do not let a battery  sit idle for more than  two months without recharging. Also due to the self-

discharge, be sure to recharge your batteries before you plan to use them.  

2.  The batteries and the charger will get warm during the charging cycle. This is normal. 
3.  Keep the battery terminals clean.  
4.  Always insert the battery in the charger with the correct polarity.  
5.  If the charger does not charge the batte ries, check to see if the battery  is  dead, faulty or w orn out. All rechargeable 

batteries will eventually wear out after being used for a certain numbers of cycles. 

6.  Always keep metal contacts on both charger and battery clean by wiping the surfaces with a dry, soft and clean cloth. 
7.  Remove your batteries from the digital camera or camc order after use. These devices  will continue to drain a  small 

current from your batteries even if they are turned off. 

 
TROUBLE SHOOTING: 

 

 
If the RED (charge) LED indicator does NOT light when the charger is plugged into a power source 
and the batteries have been inserted: 

•  

The battery may not be properly inserted. Unplug the charger from power source and check to make certain the batteries 

are seated properly. 

•  

Check and make sure metal contacts on both charger and battery are clean. 

 

If the battery takes a much shorter time to reach full charge:  

• 

There may still be some power left in the battery prior to being charged.  

• 

The battery is getting old and should be replaced.    

 

If the battery is providing a much shorter operating time after being fully charged,  

•  

The battery may have sat idle without being charged for too long.

 

• 

The battery is worn out and about to reach the end of its service life. All rechargeable batteries will eventually wear out 

after being used for a certain number of cycles. 

 
SPECIFICATIONS : 

Input Power :              

 100~240V AC, 50/60Hz  

                                    

12~24VDC (for DC IN Socket) 

Output Power :            

 4.2V/8.4V DC, Max. 750mA (with Auto. Detection)

 

                                     

5.0V DC. Max. 650mA (for USB Power Port) 

Summary of Contents for XtraPower Traveler +







Reviews: