Proline IDW52P Manual Download Page 7

.6.

Starting the Appliance

GB

Starting a wash cycle

After having completed all of the installation steps in the preced-

ing paragraphs, turn on the water to the unit, partially open the

door of the dishwasher, and press the ON-OFF button "A" lo-

cated on the control panel. The "B" indicator light will come on.

At this point, the appliance is on and ready to be programmed.

Setting and Starting a wash Cycle

Choose the desired cycle by pressing the cycle selection button

"C". Each time it is pressed, one of the cycle indicator lights "D"

will come on in succession.

Choose the wash cycle you feel is most appropriate for the type

of dishes that need washing (consult the wash cycle table con-

tained in this manual, especially when first using the appliance).

Close the door and the indicator light “D” will begin to blink indi-

cating that the wash cycle has begun and cannot be modified. If

necessary, read the paragraph entitled, "Cancelling or modifying

a cycle while underway". The end of the cycle will be signalled by

six acoustic sound, and the indicator light "D" will turn off.

Cancelling or modifying a cycle while underway...

Premise: A cycle that is underway can only be modified if it has

only been running for a short time.

Otherwise, the detergent may have already been used, and the

appliance may have already drained the wash water. If this is the

case, the detergent dispenser must be refilled (see the paragraph

entitled, "Loading the Detergent").

To change the cycle currently underway, open the door, press

the ON-OFF button "A" to turn the machine off and then open the

door.

To set a new wash cycle, follow the instructions contained in the

paragraph entitled, "Starting a Wash Cycle".

If you forget to load some of the dishes...

The wash cycle can be interrupted by opening the door carefully

(in order to avoid being sprayed by hot water). Acoustic sound

will be heard and all cycle indicator lights will flash. When the

door is closed again, the cycle will automatically restart at the

point where it left off.

At the end of the wash cycle...

The end of the cycle will be indicated by six acoustical signal,at

the same time the "D" indicator light will turn off. Open the door,

turn off the appliance using the ON-OFF switch and turn off the

water supply to the unit. Wait a few minutes before removing the

dishes so as to avoid handling them while still hot (when they

are more susceptible to breakage) and to get better drying results.

Summary of Contents for IDW52P













Reviews: