background image

11

ECLFR2KTU-DY

 -

Fan Mode

 - Fan Speed. Select the fan speed (

Auto, On, Off, Silent

) using the knob.

 -

Factory Reload 

- To reset the unit. Select 

Yes

 or 

No

 and select the knob to confirm.

•  Press repeatedly the knob to return the menu mode. 

3.9 INFORMATION

To view all the information on the device, proceed as follows:
•  Press the knob to access the main menu. Rotate the knob to select 

Information

, then press it to access 

the next menu.

•  Rotate the knob to scroll through the menu, then select one of the following informationa nd press it 

to display it.

 -

Fixture Time

 - To view the operating time of the projector.

 -

Software Version

 - To view the firmware version will show on the display.

 -

UID

 - To view the identification ID for the RDM control.

•  Press repeatedly the knob to return the menu mode.

3.10 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the first unit in line; other units will work as slave.
•  Press the knob so many times until the display shows 

Stand Alone

, then press it.

•  Select 

Master/Slave

.

•  Using knob, select the desired mode and then press the Knob.
•  Press the knob to go back or to meet the waiting time to exit the setup menu.
•  Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the 

units. For longer cable runs we suggest a terminator at the last fixture (see page 13).

•  Set the slaves to the same DMX modes.
NOTE: the unit, set in Static or Effect mode, always appears to be Master.

3.11 EFFECTS MODE

This fixture has a built-in automatic program. To access this, please see the below instructions:
•  To enter the 

Effects

 mode, press the knob to access the menu.

•  Rotate the knob select 

Stand Alone

, then select 

Effect. 

Press it to confirm

•  Use the knob to select the desired program 

Effect 1

Effect 2

Effect 3, Effect 4

, then press it to confirm.

•  Set the value (

1 - 100

), then press the knob to confirm.

NOTE: after selecting the described mode, the unit will be Master.

3.12 STATIC MODE

This fixture has the ability to accept custom static color settings. Access these chases via the control panel 
on the back of the fixture.
•  To enable the static mode, press the knob repeatedly until 

Stand Alone 

shows on the display.

•  Set the strobo value 

Strobe

 

(

000 - 255

), through the knob, then press it to confirm.

•  Set the dimmer value 

Dimmer

 

(

000 - 255

), through the knob, then press it to confirm.

•  Press repeatedly the knob to return the menu mode. 
NOTE: after selecting the described mode, the unit will be Master.

Summary of Contents for ECLFR2KTU-DY





































Reviews: