manualshive.com logo in svg

ProLights ARENACOB4FC, User Manual

Share
Download
ProLights ARENACOB4FC User Manual Download Page 21

ARENACOB4FC

20

- 4 -  MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• 

Make sure the area below the installation place is free from unwanted persons during setup.

• 

Switch off the unit, unplug the main cable and wait until the unit has cooled down.

• 

All screws used for installing the device and any of its parts should be tightly fastened and should not be 

corroded.

• 

Housings, fixations and installation spots (ceiling, trusses, suspensions) should be totally free from any 

deformation.

• 

The main cables must be in impeccable condition and should be replaced immediately even when a 

small problem is detected.

• 

It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or other 

particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the main 

plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part 

dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the 

unit and cause damage to it.

4.3 TROUBLESHOOTING

Problems

Possible causes

Checks and remedies

Fixture does not light up

• 

No mains supply

• 

Dimmer fader set to 0

• 

All color faders set to 0

• 

Faulty LED

• 

Faulty LED board

• 

Check the power supply voltage

• 

Increase the value of the dimmer channels

• 

Increase the value of the color channels

• 

Replace the LED board

• 

Replace the LED board

General low light intensity

• 

Dirty lens assembly

• 

Misaligned lens assembly

• 

Clean the fixture regularly

• 

Install lens assembly properly

Fixture does not power up

• 

No power

• 

Loose or damaged power cord

• 

Faulty internal power supply

• 

Check for power on power outlet

• 

Check power cord

• 

Replace internal power supply

Fixture does not respond to DMX

• 

Wrong DMX addressing

• 

Damaged DMX cables

• 

Bouncing signals

• 

Check control panel and unit addressing

• 

Check DMX cables

• 

Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be 

resolved by the procedure given in the table.

25

DIMMER

0~100%

000 - 255

26

STROBE

No function
Strobe Slow to Fast
No function
Random strobe Slow to Fast
No function

000 - 030
031 - 100
101 - 130
131 - 200
201 - 255

27

DIMMER FADE

Preset dimmer speed from display menu
Dimmer curve Fast to Slow

 

000 - 000
001 - 255

"

"

Summary of Contents for ARENACOB4FC
























Reviews:

No comments

Brands by name

Popular brands

Load more brands