INSTALLATION GUIDE: XUF-3760
Victory Flat Screen Wall Mounting System
The Victory Flat Screen Wall Mounting System is designed for secure installation of flat screen displays up
to 60”.
Warning Statements
WARNING:
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MINIMUM WEIGHT OF 350LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN,
AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO.
FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN
DEATH. DO NOT PLACE A UNIT WEIGHING MORE THAN 175LBS. ON THIS
UNIT.
WARNING:
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS
FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING:
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
A secure structure must support the weight, or load, of the display. When mounting to a
wall that contains wooden studs, dead center of the wooden stud must be confirmed prior to
installation.
Do not install on a structure that is prone to vibration, movement or chance of impact.
Failure to do so could result in damage to the display and/or damage to the mounting
surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of
direct heat energy. Failure to do so may result in damage to the display and could increase
the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or
damage can result from dropping or mishandling the display.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to
be installed on any surface other than wooden studs, use suitable hardware (which is
commercially available).
Contact V-Mounts with any technical / installation questions.
9531-014-022-06
Included
Hardware
Universal Washer
(Qty 8)
3” Lag Bolts
(Qty 6)
Flat Washers (Qty 6)
NOTE
: To correctly determine your hardware, please refer
to the hardware list below.
1/4" Nylon spacers
5/16" Flat washers
(metal)
9/16" Nylon spacers
(large)
1/2" Nylon spacers
(large)
Nylon sleeves
(Qty 6)
(Qty 12)
(Qty 6)
(Qty 6)
(Qty 4)
1/4" Nylon spacers
(small)
(Qty 6)
M4 x 25
M5 x 20
M5 x 50
M8 x 20
M4 x 16
(Qty 8)
(Qty 8)
M5 x 12
M5 x 16
(Qty 6)
M5 x 25
(Qty 4)
M6 x 12
(Qty 8)
M8 x 25
(Qty 6)
M8 x 30
(Qty 6)
M8 x 35
(Qty 4)
M6 x 20
(Qty 6)
M8 x 70
(Qty 4)
M6 x 30
(Qty 6)
(Qty 4)
(Qty 6)
(Qty 4)
(Qty 6)
Tool List
Phillips Head Screw Driver
Electronic Stud Finder
½” Socket and Wrench
Portable Drill
Masonry Bit for Concrete Installation
1/4” Drill Bit for Wood Installations
Level (Commercially Available)
SECURE THE PLATE TO THE WALL
1. Begin by removing all pieces of the Wall Mounting System to ensure that you have all the necessary parts.
2. Instructions for mounting will vary slightly depending on your wall construction.
Wood Stud Mounting
1. For secure wood stud mounting, the wall plate must be
mounted to two studs at least 16” apart.
2. Use a high-quality electronic stud finder (commercially
available) to locate two adjacent studs and mark their
locations with a pencil.
3. With the help of an assistant, use a level (commercially
available) and position the wall plate against the wall in
the desired mounting location.
4. Mark the right, upper and lower and the left (upper
and lower), positions of the small horizontal slots
that are in alignment with the studs.
5. You should mark four positions total.
6. Next, pre-drill a 1/4” hole in the wall stud at each
marked
location.
Continued on back page
Lag Bolt and Washer
