background image

Easy Tilt     7 

 

PUTTING THE WHEELCHAIR INTO SERVICE AND REGULAR USE 

 

It  is  important  that  all  the  wheelc

hair’s  functional  parts  are  CHECKED  ONLY  BY  QUALIFIED 

AND  AUTHORISED  PERSONNEL,  both  to  assess  its  suitability  and  to  provide  the  correct 

instructions for use to occupant and  assistant where applicable. 

If any part of the wheelchair is found to be defective, the occupant or assistant must consult the dealer to solve the problem.  

Non-observance of the indications/instructions in this manual may lead to malfunctions and/or damage to the wheelchair and/or the occupant and/or third parties. Rehateam is not liable for 
any damage to the wheelchair and/or the occupant and/or third parties caused by or resulting from the non-observance of the indications/instructions.  

Use of the wheelchair requires some of its parts to be handled. Instructions for the correct handling of the wheelch

air’s components are provided 

in the corresponding sections of this 

document. Please follow these instructions to avoid injuries. 

The installation and use of electrification, mechanical and/or electrical drive devices or any other accessory not provided by Rehateam s.r.l. at the time of delivery may result in stresses 
that were not foreseen during product testing and therefore the integrity and complete safety of the product is not guaranteed. In case of installation of any additional accessory to the 
product delivered by Rehateam s.r.l., the latter must be guaranteed by your dealer, the accessory device manufacturer, and approved by Rehateam s.r.l. 

 
 
 
 
 
 
 
 
 
 
 

 
 
 

 

 

Summary of Contents for EASY TILT

























































Reviews: