background image

cause high temperatures. 

DO NOT OPERATE THE HEATER WITH THE CAUTION INDICATOIR 

GLOWING RED.

 

 

MAINTENANCE INSTRUCTIONS 

MAINTENANCE AND CLEANING

 

1.  Before cleaning, make sure the power has been turned off at the circuit breaker panel and that the 

heating element of the heater is cool. 

2.  To maintain the external appearance of the radiator, it need only be wiped over occasionally with a 

dry duster. During the summer months, or at other times when the appliance is not in use and is 

completely cold, It should be the best opportunity to wipe over with a damp cloth.   

3.  Do not use abrasive clearing powders or furniture polish. Do not use chemical or abrasive products, 

metallic scourers and so on, which may deteriorate the surface, to clean the appliance. 

4.  Clean the appliance with a dry and sooth cloth when it is not in use,and make sure the power has 

been turned off at the circuit breaker panel and that the heating element of the heater is cool. 

5.  During the summer months,or at other times when the appliance is not in use,disconnect the power 

supply,and cover the whole appliance with a dustcloth. Moreover,keep the appliance in a dry and 

cool place. 

6.  All  other  servicing  should  be  performed  by  qualified  service  personnel.  Do  not  try  to  repair  the 

heater yourself. 

7.    To protect the heating element.When start the heater, turning the temperature control in clockwise   

slowly to terminal, the unit starts the fan first then star the heating element. When close the heater,       

 

turning the temperature control in anticlockwise slowly to off, the unit close the heating element first 

then close the fan.         

 

 

 

Summary of Contents for EH-4604B












Reviews: