background image

20

Inspect and tighten all parts of the elliptical exerciser

regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and

a small amount of mild soap.

IMPORTANT: To avoid

damage to the console, keep liquids away from

the console and keep the console out of direct

sunlight.

CONSOLE TROUBLESHOOTING

If the handgrip pulse sensor does not function proper-

ly, see step 5 on page 16.

HOW TO LEVEL THE ELLIPTICAL EXERCISER OR

ELIMINATE FLEXING IN THE FRAME

If the elliptical exerciser rocks on your floor during use,

turn one or both of the Leveling Feet (98) until the

rocking motion is eliminated.

If the elliptical exerciser flexes in the center during

use, turn the Center Foot (95) until the flexing is elimi-

nated.

HOW TO ELIMINATE RUBBING OF THE DISCS

See the drawing above. If the Discs (12) rub against

the Side Shields (14, 15) during use, make sure that

the Center Foot (95) is installed in the Folding Frame

(2). If the Center Foot is installed, loosen the two indi-

cated Bolt Sets (88) and the two M4 x 16mm Screws

(97) in each side of the elliptical exerciser.

Adjust the position of the Side Shields (14, 15) until

the Discs (12) no longer rub against them, and then

tighten the Bolt Sets (88) and the M4 x 16mm Screws

(97).

HOW TO ADJUST THE BELT

If the pedals slip

while you are

pedaling, even

while the resis-

tance is adjusted

to the highest set-

ting, the belt may

need to be adjust-

ed. To adjust the

belt, first carefully

pry off the left

Disc Cover (13)

using a flat screwdriver. Next, remove the four Screws

(not shown) from the center of the left Disc (12).

Gently rotate the Disc Cover and the Disc away from

the elliptical exerciser.

Loosen, but do

not remove, the

three 1/4" x

19mm Button

Screws (114).

Insert the shaft of

a screwdriver

downward

between the

Idler (47) and the

Idler Pulley (48).

Pull the top of the

screwdriver

toward the rear of the elliptical exerciser until the Belt

(96) is tight, and then tighten the three Button Screws.

Reattach the left disc with the four screws and then

reattach the left disc cover.

MAINTENANCE AND TROUBLESHOOTING

98

95

97

14, 15

12

2

88

47

13

12

48

114 96

Summary of Contents for 780 Cse Elliptical





























Reviews: