ProForm 615 T Treadmill Page 6 User Manual Download

Page: 6 / 32

#8 x 1/2" Ground

Screw (3)–1

Base Foot

Spacer (94)–2

#8 x 3/4" Screw

(1)–8

3/8" Star

Washer (11)–6

1/4" Star

Washer (12)–8

#8 x 1/2" Screw

(3)–8

#8 x 1" Tek Screw

(5)–4

3/8" Nut (10)–5

5/16" Star

Washer (13)–4

#10 x 3/4" Screw

(2)–4

3/8" x 4" Screw (7)–4

5/16" x 1"

Bolt (4)–6

5/16" x 2"

Screw (4)–4

1/4" x 1"

Bolt (9)–4

3/8" x 1 3/4" Bolt (6)–1

3/8" x 2" Bolt (8)–5

5/16" x 1" Flat Head

Bolt (3)–4

3/8" x 1 1/2" Screw (14)–2

#10 Star

Washer (12)–4

1/4" x 1/2"

Screw (9)–4

1/4" Star

Washer (12)–8

PART IDENTIFICATION CHART

Use the drawings below to identify small parts used for assembly. The number in parentheses below each draw-

ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key

number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-

tached. Extra parts may be included.

Summary of Contents for 615 T Treadmill

































Search results

Summary of Contents for 615 T Treadmill

Reviews:

Related manuals for 615 T Treadmill

Brands by name

Popular brands

ProForm 615 T Treadmill, User Manual

Search results

Summary of Contents for 615 T Treadmill

Reviews:

Related manuals for 615 T Treadmill

Brands by name

Popular brands