Profile CD7200 Installation Instructions & Owner'S Manual Download Page 15

14

16  

RANDOM PLAY

      In CD play mode, press the RDM  16  button to play all tracks of the disc in random 
      sequence. Press it again to cancel random play.

17  

RADIO SCAN

      In radio mode, press the SCN  17  button to scan up one strong radio station signal 
      at a time. If a valid radio station is detected, the station number will blink on the 
      LCD for 3 seconds before moving onto the next strong station. Pressing the 
      button again will stop the scan process and remain on current radio station.

18  

AUTOMATIC STORING & PRESET SCANNING

      In radio mode, press and hold the A.P.  18  button for more than 2 seconds to 
      activate the automatic storing function. Once activated, the radio starts search-
      ing for first 6 strong signaled stations and stores them into the preset memory. 
      After completion, the radio will tune back to the first preset memory station.
      In radio mode, press the A.P.  18  button momentarily to activate the preset 
      scanning function. Once activated, the radio starts scanning all  preset memory 
      stations for few seconds at a time while the preset memory number flashes on 
      the LCD. Pressing the button again will stop the scan.

19 

 MUTE

      Press the MUT button to silence the system. Press a second time to resume 
      listening.

20  

MONO/STEREO

      Monaural (Mono) or Stereo mode can be selected for FM tuner s reception. For 
      best quality sound, stereo mode should be selected. However, Mono mode can be 
      selected to help the reception of distant radio stations. Press the ST button to 
      select between Mono and Stereo modes.

21  

CLOCK

      Press the CLK button to display the time on the LCD for 5 seconds. To adjust the 
      time, press and hold the CLK button until the time flashes and use the V.UP  5  
      button to adjust the hours and V.DN  6  button to adjust the minutes.

22  

RESET

      The reset button should be pressed when installation is complete and also when 
      all buttons do not operate.

23  

SECURITY LED

      Designed as a theft deterrent, the red LED will flash when the unit is turned off 
      and front panel removed.

24  

LOUDNESS

      Press LUD button to immediately enhance BASS sound effect. 

,

CD7200

Summary of Contents for CD7200





















Reviews: